A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced wye connected load. For the system, additional information are as follows: Ic = 11.3 cis 112 degrees amps ; and Zcn = 22 cis-16 degrees ohms What is the magnitude of the total apparent of the wye load

A balanced, three-phase, positive sequence, with grounded neutral source, supplies power to a balanced wye connected load. For the system, additional information are as follows: Ic = 11.3 cis 112 degrees amps ; and Zcn = 22 cis-16 degrees ohms What is the magnitude of the total apparent of the wye load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

What is the total real power and total reactive power consumed by the three-phase load (regardless if wye or delta)?
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: Give the value of reactive power per phase seen at load 2.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the real, reactive, and apparent powers seen at load 1? Give also the power factor.
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
A three-phase 440-V, 50-kW, 60-kVA inductive load operates at 60 Hz and is wye-connected. It is desiredto correct the power factor to 0.9 lagging. What value of capacitor should be placed in parallel with each load impedance?
A three-phase alternator generating unbalanced voltages is connected to an unbalanced load through a 3-phase transmission line as shown in figure. The neutral of the alternator and the star point of the load are solidly grounded. The phase voltages of the alternator are Ea = 1020º, Eb = 102-90°, Ec = 10/120⁰ E E E The positive sequence component of the load current is (A) 1.3102-107⁰ A (B) 0.3322-120° A (C) 0.9962-120º A (D) 3.5104-81⁰ A +) + j1.002 0000 j1.002 0000 j1.0Ω vovo j1.0Ω 0000 j2.002 voor j3.002 oooo
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What is the total power drawn from the 3 phase source?
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
The magnitude of the phase voltage of a balancedthree-phase wye system is 220 V rms. Express eachphase and line voltage in both polar and rectangularcoordinates.
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C