A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 65 kN is applied to the bar. Use E = 200 GPa for A-36 steel.Determine the change in its length: ______ µm. A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 65 KN is applied to the bar. Use E = 200 GPa for A-36 steel.Determine the change in its length:1.5 mum.50 mm100 mm

Answered: Image /qna-images/answer/41aa14c2-e277-4aab-aeaf-7d381456958c.jpg

Answered: A bar made of A-36 steel has the…

A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 65 kN is applied to the bar. Use E = 200 GPa for A-36 steel. Determine the change in its length: 15m um. 50 mm 100 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Related questions

Q: Newton's law of cooling states that dT/dt = k(T−t0), where T(t) is the temperature of the body that…

A: Given data :-Newton's law of cooling for a body dT/dt = k(T−t0) To find: Solve the differential…

Q: What is the unit of strain? Select all correct answers. m/m no unit mm/mm mm

A: Strain is ratio of change in dimension to the original dimension.

Q: In one of the pilot plants, a 30 m diameter horizontal axis wind turbines (HAWT) are mounted with…

A: In this problem, we will estimate the power ratio of the wind turbine by using the rotor height…

Q: Find the work done by the engine cycle shown in the P-V diagram below. P(kPa) 200 100+ a. 3.0 kJ O…

A: Given data P-v diagram of power producing cycle Brief introduction. Work done = area of p-v…

Q: 5. The cross section of a beam and its neutral axis is shown in below. The yield stress of the beam…

Q: The tongs are used to grip the ends of the drilling pipe with the center at C. a) At what angle 6…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Problem 3 Determine the support reactions of the simply supported beam loaded as shown below. 5K…

Q: A gas mixture consists of 9 kmol H2 and 2 kmol of N2 . Part A Determine the mass of H2 . Express…

Q: 1.a Injecting a gas (usually air or oxygen) at the bottom of a tank so that the turbulence caused by…

A: e. CIO is called the Hypochlorite ion. It is important in the chemical chlorination process. The…

Q: A space has occupancy of 35 people engaged in sedentary activity from 8:00 A.M. to 5:00 PM. The…

Q: A piston is moving through a cylinder at a speed of 19 ft/s, as shown in the figure. The film of oil…

Q: 2. A cooling tower is used to cool a jacket water loss from the engine. The heat generated by fuel…

A: GivenQ=2500kWQloss=30% of Q∆T=15oC

Q: Steam at a rate of 10 g/s exiting the turbine of a power plant at 100 C is to be condensed in a…

Q: Three belts move on two pulleys without slipping in the speed reduction system shown in the figure.…

A: Given Data: The velocity of point A VA=5.5 fts The acceleration of point A aA=9.9 fts2 The inner…

Q: -cm cube of stainless steel is initially at 500oC. It is suddenly immersed in a tank of oil…

Q: 3, List the truth table of the function F = xy + xy' + y'z

Q: In the design of a timing mechanism, the motion of pin P in the fixed circular slot is controlled by…

Q: A homogenous thin plate of mass 2kg and radius r = 3? cm is shown. If d is 4cm, what is the moment…

A: Given,

Q: The figure below shows a mixing tank initially containing minitial = 2500 lb of liquid water. The…

Q: You are controlling a satellite with a mass of 300 kg. The main and lateral thrusters can exert the…

A: Given: mass→m=300 kg →Fmain=600 N (in horizontal direction) →Flat=100 N (in vertical direction)…

Q: Hello i have an example with an answer , please show the solution since only the answer was shown in…

Q: A vertical circular gate is 1m in diameter is immersed in a liquid of specific gravity of 1.4. The…

Q: If a small spot of oil is spilled on the floor, a worker should: Report the spill O Clean it up…

A: The oil spill is a hazardous case of the situation in heavy industries and it should be properly…

Q: b I (0,0) * A4 AI A₂ h L D

A: Given Data- A composite shape given we have to find centroid of composite shape

Q: Draw a general schematic of this water-heating system with main inlet, branch pipes (for 1st to nth…

Q: An industrial plant has available a 4 cylinder, 3 in bove by an, stroke, 800 rpm, single-acting…

Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…

Q: 5. The temperature at the point (z,y) on a metal plate is modeled by T(x,y) 400e-(+)/2 in °C, with…

A: Given: T(x,y) = 400e-(x2+y)/2 Point = (3,5) To find: Direction in which there is no change in T

Q: A P L B MB 12M. VB

A: GivenP=10kNL=2.5m

Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…

Q: THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG…

A: Given:Barometer reading, Patm=0.099 Decabar=0.99 bar=0.99*105 PaAcceleration due to gravity, g=9.7…

Q: Refrigerant 134a enters an insulated diffuser as a saturated vapor at 60°F with a velocity of 800…

Q: Jaymar bought a small water pump for his aquarium. The pump delivers 0.2 L/s at a net head of 2 m…

Q: During a viscosity test corresponding to shear stress values of 0,30,55,80,96,110,120 pa the shear…

Q: with pv=constant In an expansion process of 0.3 kg of air from 6 bar and 0.25 m3/kg to 1 bar with…

Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…

A: Hydraulic Power is defined as the power available with fluid at entry to turbine or it is the power…

Q: Find center of area and report I and Y unit [m]

A: We have to how center of mass and show all the forces on the body shown in diagram.

Q: Seat belts and air bags save lives by reducing forces exerted on the driver and passengers in an…

Q: R = ? Fig. P2-58

Q: A pump is used to circulate hot water in a home heating system. Water enters the well-insulated pump…

A: Write the given data. V˙=0.42 gal/minP1=14.7 lbf/in2T1=180 °FP2=60 lbf/in2Win˙=125 hpρ=60.58…

Q: We begin with Direction A. (a) What is the x coordinate of the vector tail (x₁)? (b) What is the x…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 2. A 12 feet homogeneous beam AB weighing 800lb carries distributed load as shown. Support A is a…

Q: The equation representing a Bingham plastic fluid is given as T= (dv/dy) μ x Ty T= μ/((dv/dy)+ Ty)…

Q: =t 8₁ = = A₂ L₁+ L₂ (112) x AT nd the value of ♂ by taking this limit: lim 8₁. Leave the answer in…

Q: Q.4- The lower half of a 10-m-high cylindrical container is filled with water (density=1000 kg/m3)…

A: Given:Height of cylinder, h=10mHeight of water in the cylinder, hw=5 mHeight of oil in the cylinder,…

Q: What happens in the powder mixture if granulation is over wetted and under wetted? How can this be…

A: To be explained :- Effect of wetting on powder mixture

Q: Discuss the steps in the method of analysis used in solving mass, heat, and momentum transport…

A: Solution: Given Data: Discuss the steps in the method of analysis used in solving mass, heat, and…

Q: Exercises 1. The approach & efficiency of cooling tower is 10°C 4 60% respectively. If the tempe.…

Q: An industrial freezer is designed to operate with an internal air temperature of 18°C when the…

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

A bar made of A-36 steel has the dimensions shown below. If an axial force of P = 65 kN is applied to the bar. Use E = 200 GPa for A-36 steel.

Determine the change in its length: ______ µm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its length and its new cross-sectional dimensions at section a–a. Est = 200 GPa, nst = 0.29.
A bar made of A-36 steel has the dimensions shown in Figure. If an axial force of P = 80 kN is applied to the bar, determine the change in its length and the change in the dimensions of its cross-section. The material behaves elastically.
An aluminum rod is hanging from one end. The rod is 1 m long and has a square cross section 20 mm by 20 mm. Find the extension of the rod resulting from its own weight. Take E = 70 GPa and the unit weight = 27 kN/m3.
A straight bar 450 mm long is 10 mm in diameter for the first 200 mm length and 20 mm in diameter for the remaining length. If the bar is subjected to an axial push of 10 kN, determine decrease in length of the bar. Take modulus of elasticity of bar material E = 2 × 105 N/mm²
A steel bar 300 mm long, 50 mm wide and 40 mm thick is subjected to a pull of 300 kN in the direction of length. Determine the change in volume. Take E = 2x105 N/mm2and μ= 0.25.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
A stepped circular bar having diameters of 20 mm, 15 mm, and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm is subjected to an axial tensile force of 5 kN If E= 100 GPa and ν= 0.32 for the material of the bar determine: Total change in length. Change in each diameter.
A stepped circular bar having diameters 20 mm, 15: mm and 10 mm over axial lengths of 100 mm, 80mm and 60mm is subjected to an axial tensile force of 5 KN. If E= 100 x 103 N/mm2 and 1/m = 0.32 for the material of bar, determine total change in length and change in each diameter.
A bar has a length of 200 mm and cross-sectional area of 7500 mm2. Determine the modulus ofelasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm.The material has linear-elastic behavior.
A stepped circular bar having diameter 20 mm, 15 mm and 10 mm over axial lengths of 100 mm, 80 mm and 60 mm, respectively, is subjected to an axial tensile force of 5 kN.If E = 100×103 N/mm2and Poisson’s ratio v = 1/m = 0.32 for the material of the bar, determine a) Total change in length.b) Change in each diameter.
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.