A battery bank needs to store at least 2300 Wh of energy at 56 V outside where the ambient air temperature is 0° C. You have access to lead acid batteries that have a nominal capacity of 18 Ah at 10 V at 25° C. What is the minimum number of batteries required to meet this charging requirement? Draw a schematic of the battery configuration.

A battery bank needs to store at least 2300 Wh of energy at 56 V outside where the ambient air temperature is 0° C. You have access to lead acid batteries that have a nominal capacity of 18 Ah at 10 V at 25° C. What is the minimum number of batteries required to meet this charging requirement? Draw a schematic of the battery configuration.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter2: Electrical Quantities And Ohm’s Law

Section: Chapter Questions

Problem 2RQ: What is an ampere?

See similar textbooks

Similar questions

The weight capacity of a battery is defined as q 3 V/mass. Why would a battery manufacturer be interested in this quantity?
I need help on this question, As for measure resistor value, Rmeasure = 991ohms
a. Patch clamp recording of a single ion channel yields the following results: Holding Potential (mV) Measured Current (pA) -100 -1.0 -50 0.0 0 +1.0 +50 +2.0 +100 +3.0 What is the electrical resistance (in ohms) of this channel? (keep in mind mV = 10-3 volts, pA = 10-12 amperes, and an ohm is a derived unit that is equivalent to a volt/ampere, i.e. a V/A). a.) 1 x 1010 ohms b.) 2 x 1011 ohms c.) 5 x 1010 ohms d.) 2 x 10-11 ohms e.) 5 x 10-10 ohms b. What is the conductance of this channel in siemens (S)? (keep in mind 1 S = 1/ohm) a.) 2 x 1011 S b.) 5 x 1010 S c.) 1 x 10-11 S d.) 2 x 10-11 S e.) 5 x 10-10 S c. What would be the equivalent conductance of 1,000 of these channels opened at the same time? a.) 1000 x conductance of 1 channel b.) 5 x 10-8 S c.) 2 x 10-14 S d.) 1/1000 the conductance of 1 channel e.) 2 x 108 S
For the circuit shown below, determine the power consumed by battery 1's internal resistance.
The pure silicon mold given on the side is doped with 10 ^ 18cm ^ -3 phosphorus atoms. When the electrical field is applied to the silicon mold, the resulting flux density is 500A / cm ^ 2. The resistance of the silicon cup was measured as 50 ohms. The ability to move electrons is 1200cm ^ 2 / etc. The ability to characterize holes is 400cm ^ 2 / etc. accordingly, what is the length of the silicon container.
In your own analysis what will happen to the capacity charge of the battery if it is connected in more load? Explain
Estimate the rating of an induction furnace in kW to melt two tonnes of zinc in one hour if it operates at an efficiency of 70%. Specific heat of zinc is 0.1. Latent heat of fusion of zinc is 26.67 kcal per kg. Melting point is 455ºC. Assume the initial temperature to be 25ºC
Since R1=5619.38ohm, R2=1949.32ohm and Ri=Infinite in the circuit given in the figure, write the equivalent resistance in Ohms between the terminals A-B. When making your transactions, 2 digits will be taken after the dot.
A. If the change in the input voltage of a power supply is around 2V and the change in the output voltage is 50% of that, what is percent regulation of the power supply? Choices: 200 100 50 25 B. What type of regulation is depicted in the question? Choices: line load power voltage
Please send the answer by typing only. I don't want handwritten. The subject is ( Electronic Circuits ) Q4) Give the drain current equation of JFET.
ii. Calculate the value of V0
Find the value of Rv (in ohms) needed for a full-scale reading of 250 mV.