A beam of semicircular cross section of radius r is subjected to a bending moment M having its vector at an angle to the z axis (see figure). Derive formulas for the maximum tensile stress o, and the maximum compressive stress o, in the beam for 0 = 0°, 45°, and 90°. M C. (Note: Express the results in the form a M/r³, where a is a numerical value.) r ABASY UNIVERS

A beam of semicircular cross section of radius r is subjected to a bending moment M having its vector at an angle to the z axis (see figure). Derive formulas for the maximum tensile stress o, and the maximum compressive stress o, in the beam for 0 = 0°, 45°, and 90°. M C. (Note: Express the results in the form a M/r³, where a is a numerical value.) r ABASY UNIVERS

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is of a cross- section in the form of a channel as shown in the figure STR - 2. When subjected to sagging bending moment about X-X axis, the ratio of maximum compressive stress to tensile stress is 7:3. Determine the dimension b. I need answer ASAP. Thank you!
Follow-up questions. Rate will be given! c. Calculate the maximum tensile stress in ksi. d. Calculate the angle that the neutral ads makes with the z axis in degrees.
A simply-supported beam of length 3L is. subjected to the loading shown in the figure. P L P L L It is given that P = 1 N, L = 1 m and Young's modulus E 200 GPa. The cross- section is a square with dimension 100 mm. The bending stress (in Pa) at the point A located at the top surface of the beam at a distance of 1.5L from the left end is (Indicate compressive stress by a negative sign and tensile stress by a positive sign).
Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point in an elastic material on two mutually perpendicular planes. The principal stress in the material is limited to 200 N/mm2 (tension). Calculate the allowable value of shear stress at the point on the given planes. Determine also the value of the other principal stress and the maximum value of shear stress at the point using Mohr’s Circle.
The aluminum and steel pipes shown in the figure are fastened to rigid supports at ends A and B and to a rigid plate C at their junction. T -Steel pipe %₂ Aluminum pipe Ⓡ The aluminum pipe is twice as long as the steel pipe. Two equal and symmetrically placed loads P act on the plate at C. (a) Obtain formulas for the axial stresses and in the aluminum and steel pipes, respectively. (Enter the magnitudes. Use the following as necessary: P, E E A and A.) (b) Calculate the stresses and (in psi) for the following data. (Enter the magnitudes.) P = 15 kips A₂ = 9.05 in ², cross-sectional area of aluminum pipe A = 1.16 in², cross-sectional area of steel pipe E₂ = 10 x 106 psi, modulus of elasticity of aluminum E = 29 x 106 psi, modulus of elasticity of steel psi psi
2) The rigid bar ABC is horizontal before the load Pis applied as shown in the figure. Determine the maximum safe value of P if the stress in the steel bar is limited to 300 MPa and the stress in copper bar is limited to 140 MPa. Use E = 200 GPa for steel and E = 120 GPa for copper. Neglect the weight of the bar ABC. E suges. steel bar: copper bar: A=520mm? A=320mm? A 2.00m 1.00m 1.00m 1.00m 1.50m
An element in pure shear is subjected to stresses Tgy = 3,900 psi, as shown in the figure. Consider only the in-plane stresses (the stresses in the xy plane). 4 Txy Using Mohr's circle, determine: (a) The stresses acting on an element oriented at a slope of 3 on 4 (see the figure) (Round your answers to nearest whole). psi psi psi Oz1 = Tzlyl Oyl %3D (b) The principal stresses. (Round your answers to nearest whole) Op1 %3D 01 = psi 02 = psi 3,
If the beam is subjected to an internal moment of M=30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. V Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm 150 mm M 15 mm
The section of a thick beam has the dimensions shown in the figure below. Calculate the section properties lz, ly and Izy (Izy = product of inertia) referred to horizontal and vertical axes through the centroid of the section. Refer to Section 6 in your notes for properties of planed sections. Also determine the direct stress at the point A due to a bending moment M, = 55 Nm. Ay A 5 mm 20 mm G 5 mm 5 mm 10 mm
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: Using the method of equilibrium, and NOTE: support your answer with sketches and the FBD.
The state of stress at a point in a member is shown on the element in Figure (1). Determine the following: 1) The stress components acting on the inclined plane AB (o and tx'y'). 2) The principal normal stresses (op1, p2) and max in-plane shear stress (Tmax). Do not calculate the angles of the planes of the principal stresses. Solve the problem using the equations. 8 ksi 2 ksi Figure (1) 60° B 5 ksi
A rigid bar ABCD is supported by two bars as shown in Figure below. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (1) is 590 µ. Determine: a. The normal strain in bar (2). b. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin C before the load is applied. c. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin B before the load is applied. (2) 1,500 mm 240 mm 465mm 140 mm Rigid bar B C 900 mm (1) P.