How many A binary ripple counter is required to count up to 16,38310 atFFs are required? If the clock frequency is 8.192 MHz, what is the frequency at the output of the MSB?

Q: What is the bit mask design to invert the bits in the position 0 through 3 of the register AL, while…

A: 1) We need to invert bits at position 0 to 3 while retaining bit position 4 to 7 of AL. 2) Below is…

Q: If the initial sequence number is 1 and it increment the counter by 2,56,000 for every 2sec, how…

A: Given ,  Initial sequence number=1 every 2 sec, increment the counter by 256000.  To find time to…

Q: Write the software that programs counter 1 as a BCD counter, to generate an 10 KHz square wave if…

A: Below i have answered:

Q: Write an 8086-program using the 8253 to generate a PW signal whóse frequency and pulse width can be…

A:

Q: Write the software that programs counter 1 as a BCD counter, to generate an 10 KHz square wave if…

A: Answer: I have given answered in the handwritten format

Q: How does the checksum checker know that the received data unit is undamaged?

A:

Q: In a PCM code, how many bits are required to represent 8 voltage levels of a modulating signal?

A: In a PCM code, how many bits are required to represent 8 voltage levels of a modulating signal?

Q: The EIA-232 interface has _____ pins. a. 5 b. 15 c. 25 d. 35

A: Given The EIA-232 interface has _____ pins. a. 5 b. 15 c. 25 d. 35

Q: Write an 8051 ALP to create a square wave of 50% duty cycle (with equal portions high and low) of…

A: Program:MOV TMOD,#01                       ;Timer 0, mode 1(16-bit mode)HERE: MOV TL0,#0F2H…

Q: b-For a PCM system the number of bits that represents each sample is 5bits and the bandwidth is 0.75…

A: Given : Number of bits = 5  Bandwidth = 0.75 * Maximum Bandwidth Bandwidth = 45Khz Erfc = 0.001

Q: Suppose that Fosc=16KHZ, what is the time (in milliseconds) of one tick of a 16-bit timer and using…

A: Given data :: Fosc = 16KHz  with a 16-bit timer using 1:4 prescaling. - delay =  1/ Ftimer - Ftimer…

Q: Assume that XTAL = 11.0592 MHz. What value do we need to load the timer's register if we want to…

A: It is given  that  XTAL = 11.0592 MHz and  the counter will counts up every 1.085 us. It will say…

Q: How many valid states for a modulus-N counter? Select one: ON O N-1 O 2N O N? What is the initial…

A: Here in this multiple question we have asked no of valid state in modulus N counter ..and second…

Q: For the up-counter's sizes of 8-bits, assuming a 1 Hz clock, indicate how much time would pass…

A: For the up-counter's sizes of 8-bits, assuming a 1 Hz clock, indicate how much time would pass…

Q: Given: In a Laser Circuit FSM, the output x equals 50 nanoseconds, and Tclk equals 10 nanoseconds.…

A: Answer:

Q: Write a program to count continuously in hexadecimal from FFH to 00H in a system with a 0.5 us clock…

A: Program: Address Label Mnemonics 2000H   MVI B, FFH 2002H NEXT DCR B 2003H   MVI C, COUNT…

Q: 4- Write an assembly program that count 0 FFh ( Binary counter and display the count on port B of…

A: Below is the assembly program with explanation:

Q: . Three cascaded modulus-10 counters have an overall modulus of ( .30 . A 10 MHz clock frequency is…

A: 1. (C)     The option C i.e 1000 is the correct one.  If we consider an example the individual…

Q: Write a program to monitor the RB5 bit. When it is HIGH, make a LOW-to-HIGH-to-LOW pulse on RB3.

A: Write a program to monitor the RB5 bit.When it is high,make a LOW-to-High-to-low pulse on RB3.

Q: The lowest hex address decoded by the cicuitry below is Н. A14 A0- A19 32K×4 A15 CS

A: CHIP SELECT  = A19 . A18 . A17 . (A16)'. A15                     A19 A18 A17 A16' A15 1…

Q: 74LS138 Decoders (used to generate CS signals for memory devices) can be replaced with NAND gates…

A: Given:

Q: If the sampling rate for a PCM signal is 200,000 samples per sec, what is the sampling interval? 5…

A: I have given an answer in step 2.

Q: How many transient states does a 4-bit ripple counter transit through between count = 0111 and count…

A: The main function of the counter is to count the number of pulses using a clock that can be used to.…

Q: Suppose an 8-bit binary ripple counter was built using JKFF. How many of the outputs of the…

A: The next count is nothing but number of bits changed in original number after adding 1 to it. Given…

Q: the conditions listed above the diagram what would be the binary data on the output of the 74LS157…

A: FOR SOLUTION SEE STEP NO 2

Q: if for 9bits ADC, VREF+=3V, VREF-=0 then the step size is O a. 5.10 mV O b. 6.64 mv O. 5.85 mV

A: Explanation: Given: ADC = 9bits VREF +=3V VREF -=0   Step size for this will be = 5.85 mV

Q: The highest hex address decoded by the circuit below is H. A8 A7 A6 A10- A9 ET dE2 B ROM LS 138 dcs…

A: A8 -> C, A7 -> B, A6 -> A { these are the iputs from first } A10 -> E1, A9->E2 {…

Q: A system which accepts an M-bit word and establishes the state 1' on one and only one of 2M output…

A: GIVEN:  A system which accepts an M-bit word and establish the state "1" on one and only one of 2M…

Q: What is the bit mask design to invert the bits in the position 0 through 3 of the register AL, while…

A: We have AND and OR and XOR operation options AND operation with 0000,_1111 will clear the bits from…

Q: If each step takes 3nS, then what will be the length of clock cycle?

A: The given question has asked to find the length of clock cycle if each steps takes 3nS.

Q: How many transient states does a 4-bit ripple counter transit through between count = 1101 and count…

A: When the counter transits between 1101 and 1110, 1 flip flop change i.e QA.

Q: Using timer0 in CTC mode with a prescaler value of 1024, write an assembly program to generate a…

A: here we calculate clock: delay with 6.4ms ============================================== we take…

Q: Assume the SMCLK clock is 8 MHz. What is the baud rate if the UCAxBRW equals to 833 s?

A: About bound:how many times a single changes per second. Solution below:

Q: the synchronous counters different from the asynchronous counters by less propagation operate in a…

A: Answer : Synchronous counter is faster than asynchronous counter. synchronous counter , flip flop…

Q: output should be taken from the Parity Generator/Checker IC during the read operation to store the…

A: output should be taken from the Parity Generator/Checker IC during the read operation to store the…

Q: Write an 8051 C program for timer-0 to generate a signal with 10 ms on time and 5 ms off time.

A:

Q: Write a program to count from 0 TO 9 with a one second delay between each count. At the count of 9,…

A: 8085 Assembly language program to count from 0 To 9 with one second delay .clock frequency 1 MHZ

Q: determine the binary nmbrs represented by the resulting digital output sequence for 6 pulses.Is any…

A: Dear Student, To find the binary representation we will see the enable pulse code and will only take…

Q: A 4-bit up/down binary counter is in the DOWN mode and in the 1010 state. On the next clock pulse,…

A: Given:   A 4-bit up/down binary counter is in the DOWN mode and in the 1010 state. On the next clock…

Q: For a 4-bit counter, how many clock pulses are required to generate the sequence 0 to 12 assuming…

A: The correct answer is that 12 clock pulses are required to generate the sequence.   Explanation…

Q: In QAM, the parameters that are varied are(a) amplitude and frequency (b) phase and frequency(c)…

A: GIVEN:   In QAM, the parameters that are varied are(a) amplitude and frequency (b) phase and…

Q: QUESTION 14 The duty cycle for the 8284 OSC output signal is

A: Actually, instructions can be executed in one cycle.

Q: A three bit LFSR is shown in figure below. Initially, the value of output Y = Y2Y1YO is set to 110.…

A: This question is from Linear Feedback Shift Registers (LFSR) using three bit with XOR gate and…

Q: Write and verify the HDL description of an eight-bit ring counter similar to the one shown in Fig.…

A: Given: An eight bit ring counter is shown below: We can generate eight repeated timing signals…

Q: in the single clock cycle datapath discussed in class, there are two adders, separate from the ALU.…

A: The CPU can be divided into a Data Section and a Control Section. Data section is also called data…

Q: For an 8-PSK system operating at an information rate of 36 kbps determine, 1. Baud?

A: The Answer is

Transmission media

A communication channel that transmits data from a source to a recipient is referred to as "transmission media." Electromagnetic impulses are used to transmit data. Transmission media's primary purpose is to transmit data in the form of bits via a local area network (LAN). In data transport, it is the physical link that connects the transmitter and receiver. Transmission medium is part of layer 1 or physical layer of the ISO/OSI (Open System Interconnection) model.