A block of mass m = 2 kg is resting on a rough inclined plane of inclination 30° as shown in figure. The coefficient of friction between the block and the plane is u = 0.5. What minimum force F should be applied perpendicular to the plane on the block, so that block does not slip on the plane.? (g = 10 m/s²) %3D A 30°

A block of mass m = 2 kg is resting on a rough inclined plane of inclination 30° as shown in figure. The coefficient of friction between the block and the plane is u = 0.5. What minimum force F should be applied perpendicular to the plane on the block, so that block does not slip on the plane.? (g = 10 m/s²) %3D A 30°

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Similar questions

If A = 1 kg, B = 2 kg, C = 801 kg, and the static of coefficient friction is equal to 0.04. Determine the normal force exerted by the horizontal plane to Block B. Find the force F required to start C moving upward. Nb = Blank 1 N F = Blank 2 N
A stepladder consisting of two legs pinned together at C is resting on a rough floor. Will a 800 N worker be able to change the light bulb if he is required to climb to a height of 1.3 m? The uniform legs AC and BC weigh 110 N and 70 N, respectively. The coefficient of static friction at Aand B is 0.48.
Based on the following figure if the value of F is equal to 2541 N and the angle α is equal to 26.3°. Determine the minimum mass of the block A (in kg) so that it does not slide to the right product of the force F, if it is known that the static coefficient of friction is 0.25 and the dynamic is 0.2.
Assume the coefficient of friction = 0.22, A = 175N and B = 96N. Find the least value of P to cause impending motion and the value of θ.
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
based on the following figure if the value of F is equal to 3894 N and the angle α is equal to 36.5° Determine the minimum mass of block A (in kg) so that it will not slide to the right as a result of force F, knowing that the static coefficient of friction is 0.25 and the dynamic coefficient is 0.2.
A 12 ft bar of negligible weight rests on the smooth planes as shown. Determine the angle a at which the bar will be inclined to the horizontal when it is in a position of equilibrium if T = 300 lb and x = 3 ft.
Blocks A and B weigh 50 lb and 30 lb, respectively.Using the coefficients of static friction indicated, determine the greatest weight of block D without causing motion.
A block weighing 100 N is placed on an inclined plane of slope angle 30 degrees and is connected to a secondhanging block of weight “W”, by a cord passing over a small frictionless pulley. The coefficient of slidingfriction is 0.3. Find the weight “W” for which the 100N block moves up the inclined plane at a constantvelocity.
Consider a vehicle being towed with a rope up a hill at constant velocity, and therefore in equillibrium. The vehicle has a mass of 1500 1500 kg (i.e. weight of 14.715 kN14.715 kN) that acts at the center of mass at GG. The contact between the inclined road and wheels at AA and BB are smooth, and the tyres are free to roll, so rolling resistance can be neglected. The angle θθ between the rope and the road is 5 degrres. Calculate the tension in the rope. Calculate the total net reaction force on the rear tyres at A. the towing arrangement and towing angle are changed so that the front wheels of the car are just lifted off the road. Calculate the new tension in the rope and new angle θθ made between the rope and the road.
If the beam AD is loaded as shown, determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. The coefficients of static friction at the wedge’s top and bottom surfaces areμCA = 0.25 and μCB = 0.35, respectively. If P = 0, is the wedge self-locking? Neglect the weight and size of the wedge and the thickness of the beam.
A minimum force of P = 50 lb is required to hold the cylinder from slipping against the belt and the wall. Determine the weight of the cylinder if the coefficient of friction between the belt and cylinder is μs = 0.3 andslipping does not occur at the wall.