A block P of weight 50 N is kept on a plane and now pulled so that the extension in the spring is 10 cm. The stiffness of the spring is 4 N/cm and the coefficient of friction between the block and the plane is μ = 0.3. Find the maximum compression in the spring.

A block P of weight 50 N is kept on a plane and now pulled so that the extension in the spring is 10 cm. The stiffness of the spring is 4 N/cm and the coefficient of friction between the block and the plane is μ = 0.3. Find the maximum compression in the spring.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Related questions

Q: 10.) An ideal gas with goes thru the quasistatic cycle shown to the right. The Pabs(atm) steps are: ...

Q: Using these values, draw the projectile trajectory of the tennis ball from your Experiment # 4 (simi...

Q: plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll ...

Q: Radiative heat transfer is intended between the inner surfaces of two very large isothermal parallel...

Q: A 23 mm diameter bronze bar 2.8 m long is placed between two rigid walls. At a temperature of -3°C, ...

Q: Consider a river flowing toward a lake at an average velocity of 3 m/s at a rate of 500 m³ls at a lo...

Q: Example: 5 A rigid bar AB, 9 m long, is supported by two vertical rods at its end and in a horizonta...

Q: rculated from the room maintained at 25°C DBT and 50% RH. The bypass factor of cooling coll is 0.15 ...

Q: Consider the simply supported truss as defined in the figure and parameter table. Find the force in ...

Q: A particle is traveling along the straight path. If its position along the x axis is x = (7.7t) m, w...

A: Given data: x=7.7ty=0.78x Need to determine the velocity at 4 sec.

Q: A centrifugal pump has NPSH required of 25 ft. The water temperature is 90 deg. Fahrenheit and the f...

Q: A В D 63.435° 63.435° 63.435° E F G H 5.0 5.0 5.0

Q: 2. Show the SHEAR and MOMENT Diagram, Maximum Bending Stresses (Tension and Compression), and Maximu...

A: The free-body diagram of the beam is shown below.

Q: zs A solid sphere ot redius 30 em is heated to soo°C befoce beine pleced inside of refrigerator wkos...

A: radius of sphere r=30 cmA=4πr2A=4π×.32=1.1309 m2Th=500°CTh=500°+273=773 KTR=5°C+273=278 KQ=σATh4-TR4...

Q: Example: 4 A prismatic steel bar having cross sectional area of A=300 mm? is subjected to axial load...

A: A per given question A=300mm2 E=2×103mpa We have determine increse the length of bar

Q: 300N1 50ON 01 400N enolens Isup9 1 ti ( IGups G Fy dlae J. K elque D 16ma Blob OC A TTT M23 panels@3...

Q: An overhead 25-m-long, uninsulated industrial steam pipe of 100 mm diameter is routed through a buil...

A: The rate of heat transfer through the convection is given by the formula as- Q=hA∆T where, h is the ...

Q: The ZooN farce of Fig. is the resultant of three coplanar Porces and a Coup le. Determine the force ...

Q: The right-angle uniform slender bar AOB has mass m. If friction at the pivot O is neglected, determi...

A: As per given question determine the magnitude of the normal force at A and the magnitude of the pin...

Q: Engineering applications of vapor pressure.

Q: The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the ...

Q: A particle travels along the path y? = 4x with a 3. constant speed of v = 4 m/s. Determine the x and...

Q: Steam flows into a turbine at the rate of 20 kg/s with an enthalpy of 2650 kJ/kg. Radiation losses f...

Q: Red pistoln boiling water bath at TH = 100°C. The volume of the piston is 0.52 liters. This point is...

Q: A particle travels along the path y = 4x with a 3. %3D constant speed of v = 4 m/s. Determine the x ...

Q: A particle moves along the curve y = x- (x/400), where x and y are in ft. If the velocity component ...

A: As per given Y=x-x2/400 Vx=2fts X=20ft We have to determine the magnitudes of the velocity and acc...

Q: 27°C to o.8 MPa and 50°C steadily by a T= 50°C P3=0.8 MPa compressor. Taking the environment COMPRES...

Q: d, determine the acceleration of A with re

A: NEED TO FIND ACCELERATION A WITH RESPECT TO B

Q: A Simple Rankine cyele work hetueen pressure 3400 kA9and bakparthe initialCanelitian of steam being ...

A: Rankine cycle processes 1-2 isentropic expansion in turbine. 2-3 heat rejection at constant pressur...

Q: Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level...

Q: Quiz - TMPC332 FLUID MACHINERIES Solve the problem as stated below. Make your solution clear and cle...

Q: The pressure ratio across a normal shock wave is given by the following equation: P2 P1 P2 P1 Show t...

A: The given relation to be proven is : P2P1 = γ+1γ-1ρ2ρ1-1γ+1γ-1 - ρ2ρ1

Q: A propped cantilever beam is loaded as shown. Determine the reactions at A and D (positive if the fo...

Q: 3) Figure - 3 illustrates a type of engineering chain used for conveying applications. All component...

Q: A piston cylinder device operates 1kg of fluid at 20 atm pressure . The initial volume is 0.04m^3 th...

A: Draw the P-v diagram of the system.

Q: The pressure reads 10,800 Pa. Determine the altitude at standard atmosphere. *

A: Given:- Pressure (P) = 10800 Pa To Find:- The altitude at standard atmosphere (h)

Q: A thick-walled cylindrical pressure vessel with an inside diameter of 280 mm and an outside dianeter...

Q: Given: Ammonia, P = 1.05 bar, T = -39.7°C Find: u (kJ/kg) Your Answer:

Q: ᴀ ꜱᴜʙᴍᴇʀꜱɪʙʟᴇ ᴘᴜᴍᴘ ᴅᴇʟɪᴠᴇʀꜱ 350 ɢᴘᴍ ᴏꜰ ᴡᴀᴛᴇʀ ᴛᴏ ᴀ ʜᴇɪɢʜᴛ ᴏꜰ 5 ꜰᴛ ꜰʀᴏᴍ ᴛʜᴇ ɢʀᴏᴜɴᴅ. ᴛʜᴇ ᴘᴜᴍᴘ ᴡᴀꜱ ɪɴꜱᴛᴀ...

Q: 2. The crate shown in the figure has a mass of 120 kg., coefficient of static friction HS=0.6, and t...

Q: Seventy kilojoules of work is done by each kilogram of fluid passing through an apparatus under stea...

A: GIVEN DATA -

Q: . The minimum value of P that will hold the block in place if θ is zero is nearest to? b. The minim...

Q: Find the air horsepower of an industrial fan that delivers 55 000 cubic feet of air per minute (25.9...

A: Given that, Flow rate of air, Q=55,000 ft3/min,Area of flow, A=3 ft×4 ft=12 ft2Pressure of air, Pa=5...

Q: An ideal gas is enclosed in cylinder with frictionless piston at 300 K and 2 bar. The gas expands fr...

Q: The stepped shaft shown in the figure is supported by bearings at A and B. Determine the maximum str...

Q: Example 2. A high-speed AC 130 gunship is flying at a pressure altitude of 10 km. A Pitot tube on th...

Q: Determine the Bulk modulus of elasticity of a liquid, if the pressure of the liquid is increased fro...

A: Given data, P1=70 N/cm² P2=130 N/cm² Volumetric strain is given = -∆V/V=0.15% or 0.0015

Q: If the pressure in pipe A was decreased by 10 kPa while pressure in pipe was maintained, what will b...

Q: Two springs were attached in a series as shown. The maximum Shearing stress of the spring is limited...

Q: The right-angle uniform slender bar AOB has mass m. If friction at the pivot O is neglected, determi...

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A block P of weight 50 N is kept on a plane and now pulled so that the extension in the spring is 10 cm. The stiffness of the spring is 4 N/cm and the coefficient of friction between the block and the plane is μ = 0.3. Find (i) the velocity of the block as the spring returns to its undeformed state and (ii) the maximum compression in the spring. (complete accurate solution with each steps)
A block P of weight 50 N is kept on a plane and now pulled so that the extension in the spring is 10 cm. The stiffness of the spring is 4 N/cm and the coefficient of friction between the block and the plane is μ = 0.3. Find (i) the velocity of the block as the spring returns to its undeformed state and (ii) the maximum compression in the spring. ( By principle of conservation) ( answer= maximum compression is 2.5cm) ( explain with proper steps)
A 5 kg box on a horizontal table is pushed by a horizontal force of 15 N as shown on the right. If the coefficient of friction is 0.4, will the box move?
Power is transmitted between two shafts by a V-belt whose mass is 0.9 kg/m length. The maximum permissible tension in the belt is limited to 2.2 kN. The angle of lap is 170° and the groove angle 45°. If the coefficient of friction between the belt and pulleys is 0.17, find : 1. velocity of the belt for maximum power ; and 2. power transmitted at this velocity. [Ans. 28.54 m/s ; 30.7 kW]
The component of the force along the inclined plane due to mass of the body on a inclined plane is 500N. The net force acting on the body is 100N.The force of friction is Select one: 5 N 400 N 600 N 0.2 N
A body of weight 450 N is pulled up along an inclined plane having inclination 30° to the horizontal at a steady speed. Find the force required if the co-efficient of friction between the body and the plane is 0.25
A 200 g block is pressed against a spring of force constant 1.4 kN/m until it is compressed by 10 cm. The spring rests on a horizontal plane. Determine how much the block moves before stopping if the coefficient of friction is 0.3.
A body of mass 30 kg is resting on a horizontal plane. A pull of 80 N is subjected on the body and tends the body to move. Will the body move if coefficient of friction between the body and the plane is 0.3.
A platform supported by 4 parallel springs: 2 long and 2 short springs, have a spring constant of 7.30 kN/m and 10.95 kN/m. A 55 kg box is dropped onto it from a height of 1.5m. Find the compression of each spring if the short springs are 0.1m shorter than the long springs.
There is a box with height 1.2 m, width 0.8 m and mass 50 kg. It contains a very expensive equipment, which cannot be tilted while moving. There is a rope connected to the top-right corner of the box that you can pull with. The static friction coefficient between the floor and the box is 0.4. Assuming the rope angle θ is 30 degrees and m/s2. a) Is it possible to move the box using the rope without tilting the box? (need to show details) b) What is the minimum force required to move the box on the floor?
To get up on the roof, a person (mass 85.0 kg) places a 6.20 m aluminum ladder (mass 15.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The top of the ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2.00 m from the base, as measured along the ladder. The person is standing on the ladder 3.00 m from the base, as measured along the ladder. Find the normal reaction and friction forces (in N) on the ladder at its base. (Enter the magnitudes.)
After being released from the top of a frictionless 30˚ ramp, abox of mass 20 kg slides 5.0 meters along the ramp until it hits a (massless) spring of constant k= 80N/m. Find the maximum compression of the spring.