A cantilever beam ABCD is shown in Figure QB2. (a) Determine the reaction force and reaction bending moment at point D. (b) Draw a shear force diagram and a bending moment diagram for the cantilever beam. (c) How can we locate the position at which maximum bending moment occurs? A kN/m 2 m WW Im B Figure QB2 4 kN + Im C D

A cantilever beam ABCD is shown in Figure QB2. (a) Determine the reaction force and reaction bending moment at point D. (b) Draw a shear force diagram and a bending moment diagram for the cantilever beam. (c) How can we locate the position at which maximum bending moment occurs? A kN/m 2 m WW Im B Figure QB2 4 kN + Im C D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An indeterminate beam loaded a uniformly distributed load from A to B, from B to C, a linearly varying from 0 to 6 kN/m, is fixed at C, and a roller at point A and also in point B (where it settled 25 mm downwards here). The flexural rigidity is constant from A to C. Use E = 180 GPa, I = 1024 x 106 mm4 .Calculate the reactions and draw the shear and bending moment diagram for this beam using Slope Deflection Method.
Draw the shear and bending moment diagrams for the beam shown. EI is constant. Use the force method. I have the right answer, it is: VA = 2.90 kN (↑); HA = 0 kN; VB = 6.30 kN (↑); VC = 0.40 kN (↑). To the left); B (right). I don't know how to get to this answer, please show me step by step.
Draw the shear force and bending moment diagrams for the beam shown in your solution sheets. Provide FBD F1 = 10 kN; F2 = 40 kN; F3 = 5 kN/m DETERMINE:a. maximum positive shear force in kN b.maximum negative shear force in kN c. maximum positive bending moment in kN-m. d. maximum negative bending moment in kN-m. e. the point of inflection from point C in meters.
How do we find the maximum shear and minimum moment of this diagram? when A = 265
Consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips P1 = 2 kips h = 11' b = 25' Provide all answers in kips and ft to two decimals. The sign convention is tension positive (unless noted otherwise). (both frames are the same for this problem) What is the shear force in the bottom beams (absolute value)? What is the horizontal reaction at H (absolute value)? What is the vertical reaction at I (tension positive)? What is the bending moment in the bottom beams (absolute value)? What is the bending moment in member FI (absolute value)?
(a) Figure Q2 shows a frame with tie rod at joint B and C. The beam carries a concentratedload 300kN at span BC. Analysis and sketch the shear force and bending-momentdiagram for the entire frame.
the circular bar 20m in diameter is bent into a semicircle with a mean radius of 600mm. givern P=1462N and F=800 N. 1. compute the vertical reaction at A in kN a. 886 b. 712 c. 933 d. 1232 2. compute the axial force in section a-a in kN. e. 400 f. 1266 g. 731 h. 693 3. compute the bending moment in N-m in section a-a. i. 284 j. 187 k. 667 l. 348
Determine the vertical displacement of end B of the cantilevered 6061-T6 aluminum alloy rectangular beam. Consider both shearing and bending strain energy.
10m beam is loaded with point load P1 = 100N at 2m from the fixed end support. A distributed load (W1) was also imposed with a magnitude of 100 N/m as shown. The beam is supported by a pin and a roller at locations specified in the free body diagram. what are the reactions in A and B at what distance will the shear be equal to ZERO between A and B what the computed maximum positive bending moment? Note: counterclockwise moment on the righthand side of the beam element be positive
A beam with simple supports is subjectedto a trapezoidally distributed load (see figure).The intensity of the load varies from 1.0 kN/m atsupport A to 2.5 kN/m at support B.(a) Draw the shear-force and bending-moment diagramsfor this beam. Assume that M0 at B is zero.(b) Find the required moment M0 at B so that themaximum moment in the beam does not exceed1.0 kN.m.
An indeterminate beam loaded a uniformly distributed load from A to B, from B to C, a linearly varying from 0 to 6 kN/m, is fixed at points A and C, and a roller at point B. The flexural rigidity is constant from A to C. Use E = 180 GPa, I = 1024 x 106 mm4Calculate the reactions and draw the shear and bending moment diagram for this beam using Slope Deflection Method.
A 6-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point loads 15 kN at 1.5 m from both ends. If E = 200 Gpa and I = 0.000332 m4 , determine the following using Moment Area by Parts: a.) Midspan deflection b.) Deflection at 1.5 m from the left reaction.