A cantiliver beam A m long carries a uniformly distributed load of 18 kN/m throughout its length and a concentrated load of y kN at mid-length. To minimize the displacement, a spring support is added at the free-end. Given: Spring constant, K = 0.10 mm for every 1 kN of compressive load Flexural rigidity, El = 2500 kN.m² Y w=18 kN/m # 10 # 11 #12 U Calculate the reaction (KN) at the spring support. The spring support compressed by 0.5 mm, what is the resulting reaction in KN? If the reaction at the spring support is 25 KN, what is the resulting moment (kN.m.) at the fixed end?

A cantiliver beam A m long carries a uniformly distributed load of 18 kN/m throughout its length and a concentrated load of y kN at mid-length. To minimize the displacement, a spring support is added at the free-end. Given: Spring constant, K = 0.10 mm for every 1 kN of compressive load Flexural rigidity, El = 2500 kN.m² Y w=18 kN/m # 10 # 11 #12 U Calculate the reaction (KN) at the spring support. The spring support compressed by 0.5 mm, what is the resulting reaction in KN? If the reaction at the spring support is 25 KN, what is the resulting moment (kN.m.) at the fixed end?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to the beam loaded as shown. (a)What is the Value of horizontal reaction at the fixed support?(b)What is the value of resulting couple at A?
The left half of the simply supported beam carries a uniformly distributed load of internsity 600N/m. A.Compute the value of ??? at midspan. B.If E= 10GPa, determine the smallest value of I that limits the midspan displacement to 1/360th of the span.
An L = 38-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from wA = 430 lb/ft to wC = 270 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5000 lb on the soldier beam at a = 29 ft. Determine the horizontal deflection of the soldier beam at point C. Assume EI = 3.8 × 108 lb·in.2. Deflection is positive to the left.
Use cantilver method Calculate for the axial force in kN at member CB a = 40.4 kN, b = 21.7 kN, c = 3.6 m
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
A simply supported beam AB = 9 m has a hollow rectangular cross-section with 13 cm as width, 20 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 8 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 2 m. note; sole 4 . 5.6 and 7 i) Reaction force at B in (N)= ii) Reaction Force at A in(N)= iii) The distance from B at which the shear Force value changes from "-" to "+" in (m)= iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 1 cm from the top in (N/m^2) =
A 6-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point loads of 15 kN at 1.5 m from both ends. If E = 200 Gpa and I = 0.000332 m4 , determine the following using the Double Integration Method: a.) Midspan deflection b.) Deflection at 1.5 m from the left reaction.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 16 cm as width, 23 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 7 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
Solve for: 1. Maximum W in kN if each leg resist 10.098 kN. 2. If W is 49 kN. what is the force resisting of leg DA? 3. If W is 51 kN. what is the force resisting of leg BA?
Determine support reaction at B . Given P=100 Kn L=10 m
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.615 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.320 in. If all bars are unstressed before the load P is applied, determine the normal force in steel rod (2) after a load of P = 44 kips is applied.