A capacitor of capacitance 2 uF is charged to a potential difference of 200 V. After disconnecting from the battery, it is con- nected in parallel with another uncharged capacitor. The common potential is 40 V. The capacitance of the second capacitor is (i) 6 µF (ii) 12 µF iii) 8 µF (iv) 16 µF

A capacitor of capacitance 2 uF is charged to a potential difference of 200 V. After disconnecting from the battery, it is con- nected in parallel with another uncharged capacitor. The common potential is 40 V. The capacitance of the second capacitor is (i) 6 µF (ii) 12 µF iii) 8 µF (iv) 16 µF

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 7PP: A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a...

See similar textbooks

Related questions

Q: Consider a sampled data system y(k) 5 %o U(t) ZOH S+2 By choosing a sampling interval of T=0.2s,…

A: Transfer function: It shows the relation between the output and input of the system. This is…

Q: You are asked to construct a multi-function shift register with the functionality shown**: A.…

A: "According to the Company's policy we will solve only the first part of the question since the…

Q: 1. 4.6 An electric field in free space is given as E = xax + 4zay + 4ya₂. Given V(1, 1, 1) = 10 V,…

Q: PROBLEM 1. Find IL single prime; I. double prime ; IL LL I= 0.3 AZ 60° 0° ell 8 Ω Xc150 E = 10 V 20°

Q: The open loop transfer function of a unity feedback system is given by G(s)= (s+1)…

A: Solve the problem

Q: In a balanced three-phase wye-delta system, the source has an abc-phase sequence and Van = 120/0° V…

Q: 1)For the above circuit, determine a) The value of a resistance Rv, so that there is maximum power…

A: The maximum power will transfer to the load only if the thevenin's equivalent resistance is equal to…

Q: what is the total impedance

Q: Calculate the output voltage using the circuit below for resistor components of value Rf = 470 k…

A: The solution is given below

Q: Consider the circuit shown in figure. The circuit uses an ideal operational amplifier. Assuming that…

A: The solution is given below

Q: A signal is represented in the frequency domain by the figure below. If it is sampled at 100Hz, F(w)…

A: It is given that: f=50Hz

Q: 1. What are the basic components of RC Oscillator Circuit? 2. How is the resonant frequency being…

A: As per the guidelines of bartleyby I need to answer first three questions only.

Q: 4- When a 100-kVA single-phase transformer was tested in this way, the following data were obtained:…

A: The efficiency of a transformer is a measurement of the performance factor of the windings. This…

Q: The Full load. Cu loss and iron loss of a transformer are 920 W and 430 W respectively. (i)…

A: given losses of transformer

Q: QUESTION 4: Refer to Figure 13.11 that shows the ac equivalent circuit of the gain stage of 741…

Q: 6. From the data, derive the experimental values for the resistance and compare them with the known…

A: Voltage is the potential difference across a terminal, it is measured in parallel, a device used for…

Q: In determining an expression for i(t) fort > 0 (i) (iii) Draw the circuit diagram for t < 0…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 11.63 A balanced three-phase source serves the following loads: Load 1: 60 kVA at 0.8 pf lagging…

A: The solution is given below

Q: 4. A circuit has a transfer function (8+1) H(s)-(² +65 +25) a. Determine the partial fraction…

A: A circuit has a transfer function: H(s)=s+1s2+6s+25 a) We need to determine the partial fraction…

Q: If the input x(t)= e-³tu(t) and the output y(t) = cos3t, find h(t) where the convolution y(t) =…

A: The solution is given below

Q: 11.56 In a balanced three-phase system, the source has an abc-phase sequence and is connected in…

A: Delta current: There are three windings. If the tail is connected to the head of the other winding…

Q: A transmitter has an alphabet of four letters [x1, x2, x3, x4] and the receiver has an alphabet of…

Q: Q7/A low pass signal of 3 kHz bandwidth and amplitude over -5 Volts to +5 Volts range is sampled at…

A: Low Pass Filter: A low-pass filter (LPF) is a circuit that only allows signals below its cutoff…

Q: 25 Given: Vrms = 120 V, what is its voltage at 35 degrees? 68.83 V 87.94 V 97.34 V 125.88 V

Q: Determine and draw the Thevenin equivalent for the circuit to the left of terminal a-b (ii)…

Q: given a descrete signal x[n]={...0,10,8,6,4,2,0,...} find even component and odd component

A: In this question we need to find even component and odd component of the given signal.

Q: whats the 1- controller function of the 2- rotor

A: We need to stay what is the function of a controller and a rotor.

Q: QUESTION 5: Consider the differential amplifier in Figure P11.17 with parameters V = 5 V, V = -5 V,…

A: Differential amplifier It is an electric circuit that amplifies the difference between two input…

Q: 80022 j125022 -J4502 Vs = 100 Sin (wt) V Soive for polar & Phasor form of Ziz, VR, V₂, Vc

Q: Given the NMOS circuit in Figure 2 with VDD = 18 V and the following transistor parameters: V₁=0.8…

Q: a. Find the necessary KVI/KCI. equations to solve the problem. b. Compute for 1₁, 12, and I ( c.…

A: Note: As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: QUESTION 9 One of the dangers of Series motors is : They are inherantly unstable and should never be…

A: We need to answer which one among the given option is most suitable for the question that is which…

Q: Determine the Vo for the circuits below: Si Ge + 20 V 2 ΚΩ Η 2kΩ

Q: 6- A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full- load and half-load at unity…

Q: 3.- (33) Find the h parameters for I₁ I₂ ww V₁ N R₁ R₂ V₂ the given circuit

A: In this question, We need to determine the h parameters for the given circuit. Using the virtual…

Q: An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Cu loss…

Q: Two alternators operating in parallel supply the following loads: A = 400W, unity pf; B=1000kW,…

Q: Create a 3-bit counter that counts from 001, 100, 101, 111, 110, 010, 011, 001, and so on. Provide…

Q: 4. The last step is to let one bit f determine the function of an adder/subtractor output z+y iff 0…

A: Given x + y if f=0 Output =…

Q: Given the circuit below, compute for the following, (fin = 60Hz) a. Peak to peak ripple b. Filtered…

A: In this question, We need to determine the peak to peak ripple voltage and filtered dc value? We…

Q: 11.9 Find the equivalent Z of the network in Fig. P11.9. 20 -j10 -jin Z c b 192 102 www

A: Solve the problem

Q: Example1/ For the circuit shown,if the switch on at t=0, determine Vr, ir and Vs as a function of…

A: In this question we need to find Vr , Vs and Ir as function of time .

Q: 3 Use Thevenin method to E Rs b√ UR₁ R₂ ŪRY □ RE R3 calculate |x E=240V R₁=45 R₂-30 R3 =15 Ry=20…

A: We need to simplify the given circuit using thevenin theorem

Q: 50) x y and z represent Boolean variables. If f = xy(z + 1) + xy, then one can simplify f So that f=…

A: Given, x, y and z represents Boolean variables. Function f=xyz+1+x'y

Q: - A OC MOVABLE ARM (WIPER) ов If the above potentiometer is rated for 10 kohm and the resistance…

A: Given, Potentio-meter is rated 10 kΩ Resistance between B and C terminal is RBC=2 kΩ

Q: Ao A₁ Vcc GND EN DO D1 D2 D3 MUX S₁ So F MUX Functional Truth Table: S₁ Sp F 00 DO 01 D1 10 D2 1 1…

Q: + through a conductor prove that §1.ds 7.ds = 0 For a DC current

A: The drift velocity can be explained as the average of the velocities acquired by the free electrons,…

Q: for the circuit in the FIG. (a) suppose that the elements of the circuit have values such that…

A: Given the circuit, as shown below: Given: R = 500Ω L = 10mH C = 1μF. at t > 0 the switch is…

Q: Plus the following: 8. Find Vs

A: The required parameters of the circuit can be calculated by using nodal analysis.

Q: A transformer, when tested on full-load, is found to have Cu loss 1.8% and reactance drop 3.8%.…

A: The transformer is a device used for the transfer of energy, the power can be increased or decreased…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

57. A capacitor of capacitance 2 µF is charged
to a potential difference of 200 V. After
disconnecting from the battery, it is con-
nected in parallel with another uncharged
capacitor. The common potential is 40 V.
The capacitance of the second capacitor is
(i) 6 µF
(ii) 12 µF
(iii) 8 µF
(iv) 16 µF

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwatt
This circuit is connected to a 1000-Hz line. The resistor has a voltage drop of 185 V. the inductor has a voltage drop of 740 V, and the capacitor has a voltage drop of 444 V. The circuit has an apparent power of 51.8 VA. ETITZVA51.8PFER185VIRRPEL740VILXLVARsLLEC444VICXCVARsCC
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?