A car is traveling on a -4.20% grade for a design speed of 90 kph. Coefficient of friction between tires and pavement is 0.33. Driver's reaction time (including perception time) is 2.50 seconds. Determine the following: a.) acceleration of the vehicle in ft/s2 , b.) Stopping sight distance in meters.

A car is traveling on a -4.20% grade for a design speed of 90 kph. Coefficient of friction between tires and pavement is 0.33. Driver's reaction time (including perception time) is 2.50 seconds. Determine the following: a.) acceleration of the vehicle in ft/s2 , b.) Stopping sight distance in meters.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter3: Characteristics Of The Driver, The Pedestrian, The Bicyclist, The Vehicle, and The Road

Section: Chapter Questions

Problem 10P

See similar textbooks

Similar questions

A car is traveling at a speed of 100 ft/s which accelerates 12 ft/s2. The perception reaction time for the driver is 2.40 s. If the maximum grade of the road is -3.7%, compute the following: a. Braking distance in meters b. Lag distance in meters
compute the braking distance for a car moving at an initial velocity of 80 kph and a final velocity of 60 kph. slope of roadway is +6% the coefficient of friction between road pavement and tries is 0.17, and the perception time is 3/4 seconds.
compute the required SSD for a two-way traffic in a single lane to avoid collision with a car approaching from opposite direction if both cars are moving at 80kph, perception reaction time of each driver is 2 seconds. The coefficient of friction between the tires and the pavement is 0.50. G=2%
1. A driver is travelling at 50 mph is 80 m from a wall ahead, if the driver applies the brake immediately at t=2 secs, and begins slowing down at 10m/s^2.a. Find the distance from the stopping point to the wall.b. Determine the braking time or the time during deceleration.c. Determine the average skid resistance, assuming brake efficiency of 70%. 2. A two lane road with design speed of 80 kph has horizontal curve of radius 480 m. Design the rate of superelevation. By how much should the outer edges of the pavement be raised with respect to the center line, if the pavement is rotated with respect to the center line and the width of the pavement at the horizontal curve is 7.5 m?
The stopping sight distance of a vehicle is 295 meters. Given that the acceleration of the vehicle is 3.45 m/s2 and travelling at a maximum grade of -3.5%, determine the following: a. Velocity of the vehicle in km/h b. Reaction distance in meters c. Braking distance in ft. Provide solution asap upvote guaranteed!
Vehicle performance is being tested on a large flat paved area.(i) Determine the coefficient of side friction for a car moving at a speed of 70miles/hr aroundthe curve of a radius of 400m (ii) Comment on this value of f whether it is high or low and state one disadvantage that maybe caused due very high values of f (iii) Assuming f = 0.11, for the same design speed as above calculate the minimum radius thatwill prevent sliding of the vehicle. State your answer in ft and m. (iv) Determine the degree of this curve from the radius obtained above
While traveling at a constant speed a driver saw a road block 112 m away. He applied the brakes and the car decelerated uniformly at 6.4 m/s2. It stopped 5 m from the block. The driver’s PRT is 2.2 seconds. Sketch and calculate the initial constant speed of the vehicle in kph if;a. The roadway is levelb. The roadway grade is +10%c. The roadway grade is -10%
A car is traveling at 76 mi/hr down a 3% grade on poor, wet pavement. The car's braking efficiency is 90%. The brakes were applied 320 ft before impacting an object. The car had an antilock braking system, but the system failed 200ft after the brakes had been applied (wheels locked). What speed was the car traveling at just before it impacted the object? (Assume theoretical stopping distance, ignore air resistance, and let Frl=0.015)
What should be the maximum speed (mph) of a car traveling on a leveled (zero grade) road surface if the available stopping sight distance is 400 ft? Assume 1.5 s of reaction time and braking friction coefficient of 0.35.
43. A truck was travelling uphill at 50 kph. The brakes are suddenly applied and the truck stopped in a distance of 16.1 m. If the coefficient of friction between the tires and the road surface is 0.4, what is the grade of the road?
A motorist travelling at 100 km/hr on a highway needs to take the next exit, which has a speed limit of 50 km/hr. The section of the roadway before the ramp entry has a downgrade of 3% and coefficient of friction (f) is 0.35. In order to enter the ramp at the maximum allowable speed limit, determine the braking distance (expressed in m) from the exit ramp.
Determine the minimum stopping sight distance on a -3.5% grade for a design speed of 110 kph. Coefficient of friction between tires and pavement is 0.28. Driver’s reaction time (including perception time) is 2.5 sec.