Answered: A certain gasoline gives a hydrometer…

A certain gasoline gives a hydrometer reading of 66.5 oBaume at 15.6 oC. Using the Bureau of Standards Empirical Formula, determine the HHV in kJ/kg.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Related questions

Q: The disk shown in the figure rolls without slipping on the slope with an inclination angle of alpha…

A: Given Data The mass of the disc is: md=43 kg The radius of the disc is: r=1.4 m The rolling…

Q: 7.41. In a reach of cylindrical pipe wrapped with perfect insulation (qH = 0) the absolute pressure…

A: To find: The temperature at each end. Given: The pressure at the entry is P1=690 kPa. The pressure…

Q: Given the beam, set-up the SLOPE and DEFLECTION equation using double integration method

A: Given: To find: SLOPE and DEFLECTION equation using double integration method

Q: A В G B The slender rod AB of length 0.875 m forms a 50.0° angle with the vertical as it strikes the…

Q: Make Orthographic (Front/Top/Right views) Free hand sketch of the objects shown in the pictorials.

A: Note: As per the policy, we can solve the first three subparts. Please resubmit the remaining parts.…

Q: 7.15. The thickness of the viscous sublayer (Fig. 7.7) is usually defined by the intersection of a…

A: For solution refer below images.

Q: 4.The information on a can of soda indicates that the can contains 355 mL. The mass of the full can…

A: The given information in the problem is shown in the following attached image:

Q: 2-21. Determine the magnitude and direction of the resultant force, FR measured counterclockwise…

Q: Given the measured value is 20.04mm and the true value of the measured dimensionis +-(plus minus)…

A: Firstly, we get to know about Measured value and True value: Measured value: The value which is…

Q: R B R с D The motion of a slender rod of length 0.545 m is guided by pins at A and B which slide…

A: Given: The length of the rod: →R=0.545 m When the velocity of the end Point B is zero then the…

Q: The function of a control system

A: In the complete process of any system there ate many instruments are attached and each instrument…

Q: 2. (a) What is the temperature of air molecules if their average kinetic energy is 61 meV? (b) A…

Q: 7. The mass matrix, stiffness, and damping matrices of a two DOF system are, respectively, 10 10 0.1…

A: Given: M=1002K=10-5-520C=0.1000.3F0=-10 To find: Steady state response

Q: air enters a friction less constant avea duct with velocity of 135 m/s M₁ = 0.4 CP = 1·005 kJ/kg…

A: The inlet air velocity is V1=135 m/s. The Mach number is M=0.4 The specific heat at constant…

Q: 7.44. When fluid of specific weight 50 lb/ft flows in a 6 in. pipeline, the frictional stress…

Q: Determine the y-coordinate of the centroid of the shaded area shown. 11" Parabolic 2" Answer: y = =…

Q: Which technologies supported the development of residential suburbs and nuclear families? O The…

A: Nuclear family refer to the family which consist of core members of the family, usually parents and…

Q: A steam power plant operates on an ideal regenerative Rankine cycle, Steam enters the turbine at 6…

A: Given that: For the regenerative cycle, Turbine inlet conditions are: P5 = 6 MPa = 6000 kPa T6 = 450…

Q: F2-3. Determine the magnitude of the resultant force and its direction measured counterclockwise…

Q: bar is produced from water at (12263kJ) ive kg of eam at pressure of the amount of heat supplied if…

A: The specific heat of water is 4.188 kJ/kg.K The latent heat of evaporation of water at 4.9 bar is…

Q: Problem 20-7 A pair of worm and worm wheel is designated as (2/40/10/4). The input power to the worm…

A: The input power is P= 5 kW The rotational speed is N=720 rpm The pressure angle is φ=20° The number…

Q: Determine the magnitude of reaction at A. Express your answer to three significant figures and…

A: Given data, w= 2.1 KN/m Let, NA, Bx and By are the reactions at A and B.…

Q: Question No.15: a.) Explain the tooling layout for the production of a Hexagonal bolt in a capstan…

A: The basic construction of the capston and the turret lathe are shown is below.

Q: 32.m пу ←0.5cm 12- 5cm Here you need to Hind 10.5cm Perimeter Line. x x-co-ordinate of the Centroid…

A: Centroid is defined as a point inside or outside the figure where whole are of the surface can be…

Q: Calculate AS HE for The following Wate: outdoor condition = 34°C DBT, 28°C WBT 3 Sensible heat Sdar…

A: Sensible heat per person 0.0921 kW. Latent heat per person is 100 W. Solar heat gain is 9100 W. The…

Q: The member has a brass core bonded to a steel casing. If a couple moment of 8 kN m is applied at its…

Q: The figure shown is a composite shape consists of a square and a semi-circle. Determine the polar…

Q: (a) Assume that in each fission of 235U, 200 MeV is released. Assuming that 5% of the energy is…

A: Dear Student, As you have posted two different questions but as per Q & A guidelines I will…

Q: A perfect gas mixture consists of 4 kg of N2 and 6 kg of CO2 at a pressure of 4 bar and a…

A: Given:Mixture consist of nitrogen and carbon dioxide,mn=4 kgmc=6 kgP=4 barT=25o C

Q: HYDRAULICS Support your answer with the appropriate solution and diagram. 10.A rectangular plane…

A: Given:width of plate, w=1 mDepth of plate, d=3 mAngle with the horizontal, θ=30°Depth of the top…

Q: Consider the beam shown in (Figure 1). Take www = 2.8 kip/ftkip/ft. Follow the sign. convention…

A: Given data: ω=2.8 kip/ft

Q: Know that h=0.25 m and that the gate, which has a pin connection at point C, is initially at rest.…

A: Introduction: The initial velocity of the bullet is given as, v = 550 m/s and is hitting and then…

Q: 3/103 The man and his bicycle together weigh 200 lb. What power P is the man developing in riding up…

A: Given, Weight of man and bicycle = 200 lb Riding up 5 percent grade at constant speed of 15 mi/hr…

Q: (1) In Figure 1.b., the crank OA rotates at a constant angular velocity of 12 rad/s in the…

Q: why kinetic of motion related in maritime industry

A: The field of science that studies things that are either moving or stationary is known as classical…

Q: Determine the magnitude of the vector sum V = V₁ +V₂ and the angle 0x which V makes counterclockwise…

A: To find: The magnitude of the vector V=V1+V2. Given: The magnitude of the vector V1 is 29 units. The…

Q: 1. Simple crane as shown in Fig. 1, known load P=2kN, α= 45°, ß= 30 °, the size of pulley is…

A: Given data:- P=2kN, α= 45°, β= 30, To find:- the force on rod AB and rod AC.

Q: = a(xy² + + x³) Verify that whether function (let a>0) can be used as stress function. If so, try to…

A: Solution: Given Data: ϕ=a(xy2+x3) To Find: (a) Whether the given function can be used as the…

Q: 37. d²x dı² x(0) = -1, + 4x = -5 sin 2t + 3 cos 2t, x'(0) = 1 d²x 38. + 9x = 5 sin 3t, x(0) = 2,…

Q: 1. According to the P-T diagram of a a) What is the curve A-B? What is the curve B-C?…

A: (a) A-B : bubble point line B-C : Dew point line (b) Phase at D : liquid Phase at H : Two phase…

Q: 1.4 There is a concentrated load P subjects on the slab, please draw/explain the deliver the load. B

A: Given

Q: H PROB. 8-13. -2 that of T? E PROB. 8-14. -10% C 8-14. A and B are two shafts at right angles, in…

Q: The tension in the cable attached to the end C of an adjustabl ABC is 560 lb. Replace the force…

A: GivenT=560lb

Q: AN ELECTRIC POWER PLANT OPERATES BASED ON A RANKINE CYCLE IDEAL STEAM REGENERATIVE WITH TWO FEED…

A: T[1] = 600[C] Inlet turbine temperatureP[1] = 15000[kPa] Inlet turbine PressureP[2] = 1400[kPa]…

Q: FLUID MECH Support your answer with the appropriate solution and diagram. 4. The water level in a…

Q: F2-6. If force F is to have a component along the u axis of Fu = 6 kN, determine the magnitude of F…

A: Given data:- force F is to have a component along the u axis Fu= 6 kN To find:- the magnitude of F…

Q: The compressed air network of a foundry with a volume V = 30 m³ is filled by a compressor in 4T = 30…

Q: :. V = 2k k-1 -R(T.-T) Approve that?

Q: 300 grams of Ammonia (NH3) is contained in a linear spring-loaded piston-cylinder device as…

Q: 4. Substitutional diffusion A. Requires existence of vacancies. C. Needs to overcome an energy…

A: (4) Substitutional diffusion occurs by the movement of atoms from one atomic site to another atomic…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

A certain gasoline gives a hydrometer reading of 66.5 oBaume at 15.6 oC. Using the
Bureau of Standards Empirical Formula, determine the HHV in kJ/kg.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the mass, in kg, of a a 1m3 tank containing argon gas at 600 kPa and 400 K. Report your answer to two decimal places using rounding.
Q3: The basic barometer can be used to measure the height of a building. If the barometric readings at the top and at the bottom of a building are 675 and 695 mmHg, respectively, determine the height of the building. Take the densities of air and mercury to be 1.18 kg/m3 and 13,600 kg/m3, respectively.
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer. Determine the gage pressure of air in the tank if h1 = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000 kg/m3, 850 kg/m3, and 13,600 kg/m3, respectively.
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown. Determine the gage pressure of air in the tank if h1 = 0.4 m, h2 = 0.6 m, and h3 = 0.8 m. Take the densities of water, oil, and mercury to be 1000, 850 , and 13,600 kg/m^3, respectively.
Measuring the drop in pressure with a manometer as a function of temperature within a sealed container filled with an ideal gas provides a technique to show that the magnitude of "zero absolute temperature" or OK corresponds to -273 °C. If this experiment is conducted, starting at 1 atm and 67 °C, instead of in boiling water, what will the pressure be, in mmHg, when cooled to 0°C?
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer. The tank is located on a mountain at an altitude of 1400 m where the atmospheric pressure is 85.6 kPa. Determine the air pressure in the tank if h1 = 0.1 m, h2 = 0.2 m, and h3 = 0.35 m. Take the densities of water, oil, and mercury to be 1000 kg/m3 , 850 kg/m3 , and 13,600 kg/m3 , respectively
How does a pressure measurement of 14.7 psig differ from a pressure measurement of 14.7 psia? Explain briefly.
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Fig. The tank is located on a mountain at an altitude of 1500 m where the atmospheric pressure is 75.6 kPa. Determine the air pressure in the tank if h1 =50.1 m, h2 =5 0.2 m, and h3 =5 0.35 m. Take the densities of water, oil, and mercury to be 1000 kg/m3, 900 kg/m3, and 13,600 kg/m3 respectively.
Balloons are often filled with helium gas because it weighs only about one-seventh of what air weighs under identical conditions. The buoyancy force, which can be expressed as Fb = ? airgVballoon, will push the balloon upward. If the balloon has a diameter of 12 m and carries two people, 70 kg each, Determine the maximum amount of load, in kg . Assume the density of air is ? =1.16kg/m3, and neglect the weight of the ropes and the cage
if atp pressure is 101 kpa, and total pressure of a gas is 428 kPa, its gauge pressure is
The pressure in an automobile tire depends on the temperature of the air in the tire. When the air temperature is 25 degC, the pressure gage reads 210 kPa. If the volume of the tire is 0.025 m^3, the pressure rises in the tire when the air temperature in the tire rises to 50 degC. Determine the amount of air, in kg, that must be bled off to restore pressure to its original value at this temperature. Assume the atmospheric pressure to be 100 kPa
What is h4 in kJ/kg?