A chlorine contact chamber (w = 20 ft, d = 9 ft), flowing at 8.6 MGD, is required to meet a CT = 52 mg*min/L at a [Cl]=2.0 mg/L. What is the minimum length in feet?
Q: Q4) Oil of viscosity 0.1 N.S/m² is to flow through an inclined pipe by gravity. The pipe diameter is…
A:
Q: A pipeline 15km long, a 361mm diameter and with roughness ε = 0.03mm, conveys water from a reservoir…
A: To Determine Quantity of flow, Q
Q: Example for Homework (Team Work) Draw HGL and EGL for the pipe shown in fig. Then Calculate the rate…
A: HGL and EGL
Q: If a sewer line has an outside diameter of 0.5 m and internal diameter of 0.4 m and design to holds…
A:
Q: A 25.4-mm-diameter pipeline conveys 25kg/min oil. The oil has a density of 960kg/m and a kinematic…
A:
Q: Problem #1 (Pipes Iterative Analysis): Water at 70°F flows through 100 feet of pipe 10 inches in…
A: Given, T=70°F Length of the pipe L= 100 feet D= 8 inches =0.67 m ε=0.00085 ft Head loss in pipe…
Q: Question 6 There is a pipe burst through developed orifice of 1 centimeter in diameter with leakage…
A:
Q: Consider the water distribution network. Given the information below, find the flow rate between A…
A: Solution So, in first iteration: Assume flow through AB = Q1 = 0.03946 Q2=Q3=Q4 = 0.03946 For…
Q: At point A in a pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity…
A:
Q: An existing pipeline is to be reinforced with a new one whose coefficient of pipe friction is 2/3 of…
A:
Q: It is desired to deliver 60 m3/h of water at 20◦C through 100 m of horizontal asphalted cast iron…
A: Given data in question Discharge Length Temperature Pressure difference To find out Diameter
Q: determine the flow regimes in the suction and delivery pipes.
A: Given, Q = 40 L/s or 0.04 m3/s Dsuction = 200 mm Ddelivery = 150 mm
Q: A flowrate of 3.5 ft3/s is to be maintained in a horizontal aluminum pipe (C = 150). The inlet and…
A: Given information:
Q: Determine the maximum allowable volume flow rate in L/min that can be carried through a standard…
A: Given data, Outer diameter D = 32 mm Inner diameter d = 32-2(1.5) = 29 mm = 1.14173 in Velocity v =…
Q: Answer the attached question.
A: Given:- speed = 10000acfmT=200 oF1 atmParticle density = 1200kg/m3To find:-Lappe conventional…
Q: Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33…
A: Given data: Pipe 1: Diameter of pipe A D1 =30 in Length of pipe A L1 =5000 ft Pipe 2: Diameter of…
Q: Example (HW) Draw HGL and EGL for the pipe shown in fig. Then Calculate the rate of flow through…
A: To find out the discharge in pipe A, B and C & also found out the pressure in pipe A, B and C.
Q: Water at 20°C flows through a 3 cm ID smooth brass tube at a rate of 0.002 m³/s. What is f for this…
A: Given :
Q: A fully loaded water-plane of a 420-m long supertanker has the following half-ordinates: 0.0, 8.9,…
A: Given:- To find:- Water plane area
Q: A 25 cm diameter pipe carries a (p=1.22kg/m³) (v=1.5x10-5m²/sec) at a average velocity of 8.0 m/sec.…
A:
Q: A pipe carries a flow of 5.17 cfs of oil (SG = 0.877). At one diameter is 6 inch, the pressure is…
A: Given :
Q: It is an underground pipe that receives the runoff from roadsio inlet. O Sewerage Pipe o culverts O…
A: It is an underground pipe that receives the runoff from roadside inlet Storm sewer
Q: pipeline between point A and B consists of 1000 ft of 18in followed by 800 ft of 12in…
A:
Q: Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33…
A: Given:- Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs…
Q: A cylindrical tank has a radius of 5 ft and a height of 13 ft. Set up an integral to determine how…
A:
Q: 2. Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33…
A: Given data: Pipe A: D =30 in L=5000 ft Pipe B: D =21 in L=3500 ft f=0.016 Hl=33 ft
Q: Complete solution please. 3DECIMALS thank you Determine the head loss in feet in PIPE 1 Determine…
A:
Q: A pipe 300 m long is to convey 600 liters per second of water between two reservoirs. If the…
A:
Q: A = 26.0 degrees, b = 13.33 cm, c = 7.00 cm
A:
Q: You have designed a 16-in diameter stormwater pipe to flow at a velocity of 5 ft/s when full. The…
A: Solution: Given Data: Diameter of pipe (D) =16 inch=1.33 ft Velocity of Flow=5 ft/sec Manning's…
Q: A 2-ft diameter column packed with l-teu ceramic Raschig rings was operated with air and water and…
A: Consider the given data D=2 ft. Qy=356 ft3/minT=80oF, P=1 atmR=0.7302…
Q: A 100-mm diameter pipe is connected to a 75-mm diameter pipe. If the velocity of flow in the 100-mm…
A: Solution Given that The velocity of flow in 100 mm pipe is= 2 m/s
Q: Water is flowing with flow rate 40 liter/s in a sudden contraction pipe. The diameter of the larger…
A: The given data is: Q=AV d2=200 mm d1=100 mm Q=40 l/s=A2V2 0.040 m3/s=π4×0.22V2V2=1.274 m/s
Q: A pipe line consists of successive pipes with different sections: 380-mm, 300-mm, and 250-mm pipe.…
A: This question is related to the Fluid Mechanics.
Q: Water from a pipeline is diverted into a weigh tank for exactly 15 min. The increased weight in the…
A: Flow rate = increase in weight / time =4765/15=317.67 lb/min 1lb/min=0.12 gpm Ie flowrate…
Q: 4. To monitor turbidity and chloride concentrations of incoming flow, an engineer designed a…
A: The given data is shown below: Operating velocity=13 m/s & 8 m/sPeak flow=9.5 MGD
Q: A liquid has a density of 700 kg/m³ and a kinematic viscosity of 4.27 x 10-7 m2/s. Determine the…
A: Given data- Density (ρ) = 700 kg/m3 Kinematic viscosity (ν) = 4.27×10-7 m2/s Discharge (Q) = 220 L/s…
Q: Draw HGL and EGL for the pipe shown in fig. Then Calculate the rate of flow through this pipeline…
A:
Q: determine the flow rate at pipe 1 and pipe 2 and pipe 3. please show your complete solution.
A:
Q: An oil (s.g=0.85) and viscosity of 1.8 x 10−5 m2/s flows in a 10cm diameter pipe at 0.50L/s. Is the…
A: Laminar flow - It is a smooth flow of liquid particles in layers. The fluid follows a regular path.…
Q: A pipe handles a flow rate of 35 gpm. Find the minimum inside diameter that will provide an average…
A:
Q: PROBLEM E Oil with specific gravity of 0.88 flows through a pipe which changes from 6 In. at section…
A: Given. Pressure at A and B Diameter of A and B section Elevation of A and B Discharge Calculate…
Q: 2. A cross flow horizontal shaft, paddle wheel tapered flocculation basin with 3 compartments square…
A: Since the question comprises of a number of subparts, the solution for first three subparts is as…
Q: Determine the head loss in feet in PIPE 1 Determine the head loss in feet in PIPE 5 Determine the…
A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: 10. What is the function of a surge tank? a) It causes water hammer b) Produces surge in the…
A: What is the function of a surge tank?a) It causes water hammerb) Produces surge in the pipelinec)…
Q: A certain jet fuel has a kinematic viscosity of 1.2 x 10-6 m2/s. If the fuel is being delivered to…
A: kinematic viscosity, = 1.2 * 10-6 m2/s. Discharge, Q= 200 L/ min. Diameter of pipe, D = 22.1 mm =…
Q: Homework 2 Water flows at a velocity of 1.8 m/s in a 150 mm diameter pipeline as shown in figure. At…
A: Given data, Velocity = 1.8 m/s Pa = 150 kPa Diameter at A = 150 mm Diameter at B = 50 mm ZB - ZA =…
Q: **A 32800 ft long pipeline, of commercial steel with the nominal diameter of 12 inch of schedule…
A:
Give me right solution according to the question
Step by step
Solved in 2 steps
- Given the following parameters, give the required diameter of reinforced concrete pipe needed for the project. Q discharge = 0.85 cu.m/sec Total Length = 200 meters Invert Elevation (Lowest Point) = 0.1m Invert Elevation (Highest Point) = 0.3m Velocity = 0.2m/sec Assume Concrete Pipe is FULLThe elbow flow passage volume is 0.37 m3 between sections 1 and 2. The flow rate is 0.90 m3/s and the elbow inlet and outlet pressures are 200 kPa and 130 kPa. Consider the elbow weight is negligible. Calculate the horizontal and vertical anchoring forces to hold the elbow in place. my results were Frx = 132.8kPa Fry = 76.7kPaCalculate the head loss in a circular concrete pipe flowing half filled.The diameter of the concrete pipe is 1.5 ft , length is (1000/36)ft and flow velocity is (150/36)ft/sec.
- What is the values of H(Total Head) for various conditions in an orifice.Considering the flow of an incompressible fluid through a horizontal pipe, which of the following is a correct statement? The energy grade line is always parallel to the centerline of the pipeline. The energy grade line is always above the hydraulic grade line. The energy grade line is always horizontal. The energy grade line is always parallel to the hydraulic grade line.A pipe handles a flow rate of 35 gpm. Find the minimum inside diameter that will provide an average fluid velocity not the exceed 20 ft/s.
- A trapezoidal flume of most efficient proportion has base width of 1.5 m. Its full discharge is 3 cu.m/s. If the same material were used for the most efficient rectangular section, by how much would the discharge decreased in cu.m/s? a. 0.64b. 0.72c. 0.81d. 0.932.A 25–mm diameter commercial steel pipe,50 m long,isused to drain an oil tank. Determine the discharge whenthe oil level in the tank is 5 m above the exit of the pipe.Neglect minor losses and assume f = 0.12.DIFFERENT QUESTION FOR REVISON-EXAMINATION Additional Questions: (1) A fluid of constant density flows at the rate of 15 Liters/ sec along a pipe AB of 100 mm diameter. This pipe branches at B into two pipes, BC and BD each of 25mm diameter and a third pipe BE of 50mm diameter. The flow rates are such that the flow through BC is three times the flow rate through BE and the velocity through BD is 4 m/s. Find the flow rates in the three branches BC, BD and BE and the velocities in pipes AB, BC and BE. Water is flowing through a pipe with a velocity of 7.2 m/s. Express this velocity as velocity head in meters of water. What is the corresponding pressure in kN/m2. (2) A pipe of 150mm bore is delivering water at a rate of 7500dm3/min at a pressure of 820 kN/m2.It connects by a gradually expanding pipe to a main of 300 mm bore which runs 3 m above it. The main is designed to withstand a maximum pressure of 814 kN/m2. Neglecting loses due to friction determine if the main will fail or…
- A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown below. The width of the gate is 1 ft (into the page). When the water level reaches 15 ft, the cylindrical gate opens by turning about the hinge at point A. Determine the weight of the cylinder gateA cylindrical tank has a radius of 5 ft and a height of 13 ft. Set up an integral to determine how much work is done in emptying it if(a) It is filled with molasses (which weighs 235 lb/ft3).(b) It is filled to a depth of 9 ft and the molasses must be pumped out a 2 ft pipe at the top of the tank.A concrete pipe laid on a slope of 1:1 500 is to carry a uniform flow of 5 m3/swhen half full. What pipe diameter is required? Use C = 49 SI units.