A circular gear turns 240 per hour. Through how many radians does it turn in a 24-hour day

Q: 10. Figure 6 shows two cables AB and BC supporting a 1500 N load. A C 2.50 m 2.25 m 3.00 m 1500 N…

A: Find the length of Ab and BC also find force in AB and BC

Q: Two forces F₁ and F₂ act on the screw eye. If the resultant force FR has a magnitude of 601b and the…

A:

Q: 29. Steam at 1.4 MPa, 300 deg C expand isentropically until it bevomes saturated. Determine a)delta…

A: As per our company guidelines we are supposed to answer only first 3 sub parts in case of multiple…

Q: Draw the isometric view of the given orthographic projection of the object?

A: According to the details in the kitchen we need to draw isometric view of the given object. I am…

Q: 26. Saturated steam at 3.27 MPa undergoes a T = c process until its pressure becomes 0.8 MPa.…

A:

Q: Locate the centroid of the shaded area shown. y 2. 120 40 40 30 1 30 20 20 50- 120

A:

Q: A supercritical power plant generates steam at 25 Mpa and 560C. The condenser pressure is 7.0 kpa.…

A:

Q: 1. Steam is generated at 4.1 Mpa and 440 °C and condensation occurs at 0.105 Mpa. For a Rankine…

A: Given:P1=4.1 MPaT1=440°CP2=0.105 MPaWnet=30,000 KW

Q: 3. (a) A 3200c.c. Spark Ignition (SI) V6 engine operates on a four stroke cycle at 7800RPM. The…

A:

Q: what is 6 to 10 po?

A:

Q: Problem No. 2 A body of mass 10 kg at rest is subjected to a force of 12 N. Find the kinetic energy…

A: Given data. Mass = 10kg Force F =12 N Find the kinetic energy at the end of 10 sec

Q: Q1: The following two random variables x and y are linearly correlated: 1) specify their correlation…

A:

Q: 1:- Find the power of the main electric motor required in a lathe machine to operate a steel welder…

A: INTRODUCTION: One of the traditional machines is the lathe. The lathe machine's primary duty is to…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A:

Q: A single point cutting tool with 0°rake angle is used in an orthogonal machining process. At a…

A:

Q: Q.1 Determine the force (P) shown in figure knowing that the resultant of two forcec passes through…

A:

Q: Part (1): A 30 ?? square plate is subjected to uniform pressure as shown in Figure.1. The 2D loading…

A: Givensquare plate a=30mmE=200GPa=200×103 MPaμ=0.3σx=80MPaσy=40MPa

Q: 25. Steam at 2.6 MPa, 400 deg C expand isothermically until its pressure becomes 4.36 MPa. Calculate…

A:

Q: A jet of water of diameter 60 mm strikes a stationary flat plate normally at a velocity of 26 m/s.…

A:

Q: A mass of 15 kg is at limiting equilibrium on a rough plane which is inclined at an angle of 40…

A:

Q: Determine shear yield stress using Von Mises

A: Given data;  Uniaxial yield stress=350 MPa Determine shear yield stress using (von Mises criteria) ?

Q: (b) The same engine is connected to a dynamometer which gives a brake output torque reading of 175Nm…

A:

Q: 2. (a) Define the physical processes which comprise the four stroke cycle AND Define the…

A:

Q: Locate the centroid of the shaded area shown.

A:

Q: Two forces F, and F₂ act on the screw eye. If the resultant force FR has a magnitude of 601b and the…

A: Answer: (a) The magnitude of F2 is 57.2 lb. (b) The coordinate direction angle of F2 : ◆ Angle with…

Q: Q3/ A truss shown in Figure below is made of Aluminium and it consists of two rods. The…

A:

Q: The orthographic views of an object are shown below. a) Draw its isometric drawing using a pencil.…

A:

Q: Propane gas at 18 bar and 380 K is throttled in a steady state flow process to 1.5 bar. Estimate the…

A: P=18barT=380KTo-Find:-Final TemperatureEntropy change

Q: Two forces F₁ and F₂ act on the screw eye. If the resultant force FR has a magnitude of 80 lb and…

A:

Q: If the efficiencies of a power plant, turbine and generator (in the power plant) are 0.36, 0.5 and…

A:

Q: A diesel engine has a compression ratio of 18 and a cut off ratio of 2.4. At the beginning of the…

A: as per the given in question here is the solution provided for the question 2 b for iv) The thermal…

Q: In an IC engine mechanism, the stroke of the slider is 180 mm and the obliquity ratio is 4.25. The…

A: We have, N = speed of crank = 900 rpm, clockwise Now, θ = crank speed from T.D.C. position =…

Q: In quantity flow measurement using pitot tube, is it necessary to get the average velocity?  Why?

A:

Q: Q2. The force F = 120 lb acts on the frame. Resolve this force into components acting along members…

A:

Q: The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade)…

A: Soln:- T = 10 °C        p = 1000 kg/ m^3            D= 1 m              pmin= 80 kpa           Patm=…

Q: Q2) Several water pipes intersect at the junction box illustrated in Figure. Determine the force…

A:

Q: 2. A linkage to an aircraft landing gear is shown. • The 40-kN force acting on the wheel has a line…

A:

Q: Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular…

A: We have, Diameter, d=200 mm=0.2 m,     V=3 m/s Diameter of circular plate, d1=150 mm=0.15 m (as…

Q: What are two reasons for using an air spring? Explain the action of the conventional shock absorber…

A:

Q: Uniaxial yield stress of a material is 350 MPa Determine shear yield stress using Von Mises…

A:

Q: AQ2) Air (y = 1.4) flows into a constant-area insulated duct with a Mach number of 0.20. For a duct…

A:

Q: A shaft carries four masses A, B, C and D of magnitude 10 kg, 20 kg, 15 kg and 25 kg respectively…

A:

Q: Tank A which is completely insulated contains 1 kg of oxygen at 15°C and 300 kPa. It is connected…

A:

Q: A short hollow, cast iron cylinder with wall thickness of 10 mm is to carry compressive load of 100…

A:

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A:

Q: Q2. The force F = 120 lb acts on the frame. Resolve this force into components acting along members…

A:

Q: The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at…

A:

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

A:

Q: How many reheat stages possible in Rankine Cycle and why?

A:

Q: F L h Figure Q1 b) State if the cantilever beam is in plain stress or plain strain and explain…

A: given; lets take width of beam=b lets take reaction force=R

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.