A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the figure. The rod is perfect contact with the wall on the left side and there is a gap of 0.2 mm between the rod and the wall on the right side. If the temperature of the rod is increased by 200°C, MPa. the axial stress developed in the rod is_ Young's modulus of the material of the rod is 200 GPa and the coefficient of thermal expansion is 10-5 per°C. 250 mm -0.2 mm

A circular metallic rod of length 250 mm is placed between two rigid immovable walls as shown in the figure. The rod is perfect contact with the wall on the left side and there is a gap of 0.2 mm between the rod and the wall on the right side. If the temperature of the rod is increased by 200°C, MPa. the axial stress developed in the rod is_ Young's modulus of the material of the rod is 200 GPa and the coefficient of thermal expansion is 10-5 per°C. 250 mm -0.2 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. If P=100kN, and the plate thickness is t=8 mm, determine the maximum axial stress in the structural component shown below.
The cross section is elliptical as shown in the figure and the uniform thickness t=5mm The pressurized air tank of is receiving internal pressure p=1.4 MPa. Find the maximum axial and circumferential stresses
Figure Q3 (a) shows a cantilevered beam ABC carrying a pure moment of M kN.m at point B. Thecross-sectional area of the beam is shown in Figure Q3 (b). The yield stress of the material is 250 MPa and the material is assumed to behave linearly elastic-perfectly plastic.a) Where is the critical location for the beam and give ONLY ONE (1) reasonb) Determine the moment to initiate yielding in the cross-section of the beamc) Find the value of M that can cause plastic collapse (fully plastic) in the cross-section of the beamat the critical location and sketch the variation of stressd) If the TOTAL DEPTH of the plastic zone to be 20 mm at the critical location, WITHOUT ANYCALCULATION, sketch the variation of stress.
A beam ABC with a cantilever from B to C supports a uniform load of 3 kN/m over its entire length (see figure). The beam is a gutter with the dimensions shown in the figure. The moment of inertia about the z axis (the neutral axis) is equal to 210 cm⁴ . Calculate the maximum stress in tension σt and the maximum stress in compression σc due to uniform loading.
1. A 18-mm-diameter steel wire 150 m long, is suspended vertically from one end. It supports a tensile load of 12 kN at the lower end. Neglect the weight of the wire. Use E =200,000 MPa.a. Find the stress in the wire in MPa.b. Find the elongation of the wire in mm.
A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal Diameter:4 meters Height:6 meters Determine the circumferential stress in the walls of the water tank and longitudinal stress at the bottom of the water tank if the internal pressure inside the tank is 7.36 MPa. Answer should be in MPa.
The stress of a gate-shaped structure is shown in the figure below. Assuming that the EI of the entire beam section is constant, try to analyze the stress state of the structure, and calculate the reaction forces at points A and D.
The system shown in the figure has an acceleration of 0.5 m / s^2. Kinetic friction between blocks and surface that the coefficients are the same for both inclined planes accepting that a) the kinetic coefficient of friction b) in the rope find the stress
In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit N) act on the side faces of the cube whose dimension a = 20 mm. The limit stress for the uniaxial stress case in the material is 40 / Mpa safety coefficient n = 2. How many Newtons (N) is the largest P value according to the Von Mises assumption for the cube to be safe? please please fast help me
11.17:A bending moment of M = 700 N.m is acting on the cross section shown in the figure. Find the largest and smallest stress in the cross section. Answer: ϭmax=5,42 MPa; ϭmin=-2,01 MPa
A 100- m steel tape is used to measure the distance of the line and found to be 1,539.28m long. During measurement, the tape is supported the ends under a pull of 10kg and the observed mean temperature is 31°C. The tape is of standard temperature of 20°C and a tension of 12kg. The cross sectional area of the tape is 0.035 sq. cm. The coefficient of linear expansion is 0.0000116/°C and the modulus of elasticity of steel is 2.0 x 106 kg/ sq. cm. The tape weighs 1.5kg. a. Determine the total correction for temperature. b. Determine the total correction due to sag. c. What is the correct length of the line?
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 450 mm2. Determine the average axial stress in each bar. q = 5 t = 0