Required informationA circular plate with weight WB. Shaft AC is fixed and frictionless.-210 k lb acting at its center, point F, is supported by cord DE and a thrust bearing at=E 12 in.-- 12 in.-11 in.B5 in.10 in.D(9, 18, 3) in.F (5, 13, 5) in.Determine the cable tension for the circular plate.The cable tension for the circular plate isIb K

Answered: Image /qna-images/answer/b1b2e1da-3744-4969-9c5b-fe30b97678e7.jpg

A circular plate with weight W B. Shaft AC is fixed and frictionless. -210 k lb acting at its center, point F, is supported by cord DE and a thrust bearing at = 12 in.-- 12 in.- E 11 in. 5 in. 10 in. y D (9, 18, 3) in. F (5, 13, 5) in. Determine the cable tension for the circular plate. The cable tension for the circular plate is

A circular plate with weight W B. Shaft AC is fixed and frictionless. -210 k lb acting at its center, point F, is supported by cord DE and a thrust bearing at = 12 in.-- 12 in.- E 11 in. 5 in. 10 in. y D (9, 18, 3) in. F (5, 13, 5) in. Determine the cable tension for the circular plate. The cable tension for the circular plate is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Similar questions

Is this statement true? i) A practical rigid body does exist.
Hoop stress is limited to (2.4)MPa and density of flywheel material is (7504) Kg/m3
A square thread jackscrew has a 2 threads per inch. It is to lift 15tons. The friction radius of the collar is 1 in. The coefficient offriction between the threads of the screw and base is 0.15, thatbetween the screw and the collar is 0.13. Determine:a. The diameter of the root of the screw if theallowable stress in compression is 6 000 psi.b. The torque required to turn the screw.c. The pull required at the end of a 5 ft bar raises theload.d. The twisting moment exerted at the root of thethreads.e. The power output of the screw if it is turning at 60rpm.f. The power input of the screw.g. The efficiency of the screw and collar
Draw the free body diagram of this problem
A horizontal L=1.2 m long mb=14 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 23° angle with horizontal. A 24 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of horizontal hinge force.
A uniform rod of weight mg and length L is in equilibrium on a frictionless support as shownin the above figure. Find θ.
The bar is 10m long. A mass of 40kg places at 9m from left end of bar. Where should a 60kg mass be placed to balance the bar?
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 20 in. The generator output is 40 Hp, 3600 rpm and 90% efficiency. If there are 10 bolts, determine the force acting on each bolt in kN.
By what distance h does the cage shown in thefigure move downward when the weight W is placedinside it? (See the figure.)Consider only the effects of the stretching of thecable, which has axial rigidity EA =10,700 kN. Thepulley at A has a diameter dA = 300 mm and the pulleyat B has a diameter dB = 150 mm. Also, the distanceL1 = 4.6 m, the distance L2 = 10.5 m, and the weightW = 22 kN. Note: When calculating the length of the cable, include the parts of the cable that go around thepulleys at A and B.
Imagine that a long steel wire hangs vertically from a high-altitude balloon.(a) What is the greatest length (feet) it can have without yielding if the steel yields at 44) ksi?(b) If the in wire hangs from a ship at sea, what is the greatest length? (Obtain the weight densities of steel and seawater from Table I-I. Appendix I.)
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350