A Class C amplifier is as shown in Figure Q2(c) below. Determine: +Vcc =+60 V L7 = 15 µH Cr= 120 pF Ry= 202 R= 40 k2 R3 Figure Q2(c) (i) Sketch the AC and DC load lines. Label the key points on the load lines with the calculated values. (ii) Resonant frequency. (iii) Quality factor Q of the coil in the tank circuit.

A Class C amplifier is as shown in Figure Q2(c) below. Determine: +Vcc =+60 V L7 = 15 µH Cr= 120 pF Ry= 202 R= 40 k2 R3 Figure Q2(c) (i) Sketch the AC and DC load lines. Label the key points on the load lines with the calculated values. (ii) Resonant frequency. (iii) Quality factor Q of the coil in the tank circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Table Q2 shows the datasheet comprising the parameters of a practicalop-amp. Please answer the following questions with reference to the data inTable Q2. Determine the full-power bandwidth for a 10-V output. Using the typical values from Table Q2, find the magnitude of thecommon-mode gain, Acm.
For the circuit as shown, find R3 to set ID3 = 0.8 mA with VDD = VSS = 10 V, and ID4 = 4 mA. Calculate a new R4 to maintain Vo = 0 V. Calculate the poles of the amplifier and calculate RZ to cancel the right-half plane zero. Find the unitygain frequency such that the phase margin is set to 70◦. For the phase margin calculation, assume the dominant pole contributes 90◦ of phase shift at the unity-gain frequency. Calculate the CC required to achieve the desired unity-gain frequency and phase margin.
In a summing inverting amplifier,Rf is 100k ohms, V1 is a sinusoid with 2V amplitude and frequency of 1Hz ,R1 is 10k ohms, V2 is a sinusoid with 3V amplitude and frequency of 1Hz, and R2 is 10k ohms. Vs+ = 18 V and Vs- = ground. What is the output voltage? Please draw the waveform as well.
solve a,b and c please. a. Define on-off ratio. Why series JFET has higher on-off ratio as compared to shunt JFET? b. Compare inverting and non-inverting amplifier? c. calculate the closed loop gain of the circuit diagram given below.
(a) Define bandwidth of an amplifier and provide explanation using a diagram. (b) A circuit has no lower cut-off frequency but has an upper cut-off frequency of 100 MHz. What is its bandwidth?
1. For n-stage analog amplifier circuit, if the voltage gain of each stage is Adi and the op amp common-mode rejection ratio is CMRRi (I =1~N): a) derive the mathematical expressions for the CMRR for the whole circuit b) analyze which stage’s CMRR has the most influence on the overall CMRR.
Design an inverting amplifier to provide a closed-loop voltage gain of Ay = -22 V/V. The maximum input voltage signal is 30 mV with a source resistance in the range of 1 kls R, < 3 kN. The variable source resistance should introduce a difference in the gain no more than a 2% of the gain factor. What is the range in output voltage?
Figure 1 shows the equivalent circuit of a voltage amplifier with a source and aload connected to its input and output, respectively. Suppose that the sourceinternal resistance is Rs = 5 kΩ, the amplifier input resistance is RIN = 95 kΩ, theamplifier gain is A = 100, the amplifier output resistance is ROUT = 150 Ω and theload resistance is RL = 5 kΩ. For a sinusoidal input with amplitude VS = 5 mV, whatis the amplitude of the voltage VL across the load resistor RL? What would thevoltage across the load be without the amplifier?
Could you please solve c) and d) parts of this quesiton and explain step by step. Design a BJT collector feedback amplifier network pointing out input and output terminals with β=200, Zi=1 kΩ. When an input signal Vi=10 mV AC and Ii=1 mA AC is applied to the network, an output AC signal Vo=2V AC with output current Io=60 mA AC is obtained. a) Draw the BJT amplifier network you prefer to design and explain why you choose this network. Explain the aims and reasons in using of all the peripheral components handled on your network b) Draw AC equivalent re model of the network c) Calculate Vcc, RF, RC, Zo, and Av d) Find the output signal Vo , if Vi = 50 mV DC is applied to the input instead of 1 mV AC.
The no-load voltage gain of the amplifier used in the circuit in the picture is K = 2000, input resistance R1 = 50K and output resistance Ro = 500ohm.a) Calculate the voltage gain of the circuit Vo / Vg.b) Calculate the value of the capacitors C1 and C2, considering that the lower cut-off frequency of the circuit is 20Hz and the asymptote slope is desired to be 40db / decade.c) Calculate the upper cut-off frequency of the circuit.
Convert the inverting amplifier shown to thetransresistance amplifier as shown(66) using a Nortontransformation of vi and R1. What are the expressionsfor iTH and RTH? Write a expression forthe gain vo/vi.
For amplifier design, consider a very large load resistance RL . Use a 15 V DC source and a sinusoidal input signal of 200 mVpp and 1 kHz. Hint: you can start by choosing a collector (Icq) or drain (IDQ) operating current between 5 mA and 10 mA. 1. Design an input stage with a common drain amplifier that complies with thefollowing specifications: Voltage gain greater than or equal to 1 (Av1 ≥ 1). Input impedance greater than or equal to 250 kΩ (Zi1 ≥ 250 kΩ). Output impedance less than or equal to 2 kΩ (Zo1 ≤ 2 kΩ). Low cut frequency less than or equal to 20 Hz (fcb1 ≤ 20 kHz). Use a 2N3819 (NTE312) transistor.