A closed cylindrical vessel contains a fluid at a pressure of 625 psi. The cylinder, which has an outside diameter of 64 in. and a wall thickness of 1.000 in., is fabricated from stainless steel (E = 28,000 ksi; v = 0.27). Determine the increase in the length of the cylinder. 16 ft 0.0306 in. 0.0383 in. O 0.0414 in. O 0.0279 in. O 0.0359 in.

A closed cylindrical vessel contains a fluid at a pressure of 625 psi. The cylinder, which has an outside diameter of 64 in. and a wall thickness of 1.000 in., is fabricated from stainless steel (E = 28,000 ksi; v = 0.27). Determine the increase in the length of the cylinder. 16 ft 0.0306 in. 0.0383 in. O 0.0414 in. O 0.0279 in. O 0.0359 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3) when we put in the class tube have diameter 1.5 mm liquid with mass density900 kg/m3 , the liquid rise in the tube about 15 mm . Calculate the surface tension force?
The tank is filled with a liquid that has a density of 900 kg/m3. Determine the resultant force that it exerts on the elliptical end plate, and the location of the center of pressure, measured from the x axis.
3. A vertical piston-cylinder device on the left containing a gas has a mass of 40 kg and a cross-sectional area of 0.012 m². The local atmospheric pressure is 95 kPa, and the gravitational acceleration is 9.81 m/s². Determine the absolute pressure (kPa) inside the cylinder. (2 decimal)
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
The masses of the frictionless cylinders A and B in FIG JWU are 2.0 kg and 1.0 kg, respectively. The smallest value of the force P that will lift cylinder A off the horizontal surface is 55.5 N. 24. Calculate the radius R of the cylinder B.a. 12.5 mm b. 15 mm c. 10 mm d. 16 mm 25. Determine the reaction of the wall at cylinder A.a. 58.87 N b. 29.43 N c. 55.5 N d. 9.81 N
A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 43 kg/s. Another identical elbow is attached to the existing elbow such that the water flow makes a U-turn as shown in the second figure. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. Take the density of water to be 1000 kg/m3.
Please be clear with your soltuion. In the figure, x=25cm initially. If the pressure at m is increase by 35 KPa while maintaining the pressure at n constant. Calculate the new value of x.
Calculate the horizontal displacement of point B. EI is constant for all members (p=50kN , W=90KN/m , h=7m , b=5 m) I need a solution within 40 min
A thin cylinder 200mm internal diameter, 3mm thick has its ends closed with rigid plates. The cylinder is then filled with water. When an external axial pull of 60KN is applied to the ends then the water pressure is observed to fall by 0.1N/mm2.Determine the value of Poisson’s ratio. Take E = 170,000N/mm2, K=2000N/mm2.
Compute the height of capillary rise for water in a tube having a diameter of 0.05 mm (in SI units).
1. A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible weight. The water surface remains at the top of the gate. Determine the vertical component of the hinge force in kN to maintain equilibrium. Write your answer to the nearest three decimal places. Use unit weight of water 9.80 kN/m^3.
Determine the ybar in meters centroid of the figure shown. Where r2=12 m and r1=4 m