A Cockcroft-Walton type voltage multiplier has six stages with capacitances, all equivalent to 0.03µF. The supply transformer secondary voltage is in the range of 100 kV - 200 kV at a frequency of 150 Hz ~ 220 Hz. If the load current to be supplied is 6 mA, determine: i. the percentage ripple ii. the regulation ii. the optimum number

A Cockcroft-Walton type voltage multiplier has six stages with capacitances, all equivalent to 0.03µF. The supply transformer secondary voltage is in the range of 100 kV - 200 kV at a frequency of 150 Hz ~ 220 Hz. If the load current to be supplied is 6 mA, determine: i. the percentage ripple ii. the regulation ii. the optimum number

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.
Draw the equivalent circuit for a single-phase transformer with all the components referred to the primary side. Give a brief description of what each circuit component represents, and indicate how the secondary voltage and current are subsequently calculated from the primary side values.
Q-3 A Cockeroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 µF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
In a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic i.e, fast system response? How about when duty cycle changes slowly i.e, slow system response?
Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm Regulation of transformer at 0.5 p.f. lagging current The magnetizing current and reactance component of no-load are.........amper , .........ohm The working current and resistance component of no-load are.........amper , .........ohm *
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and secondary resistances are 0.55 ohm and 0.035 ohm respectively. The corresponding leakage reactances being 4.22 ohm and 0.18 ohm. The load is equivalent to a coil of resistance 3.85 ohm and inductive reactance of 4.2 ohm. Determine the terminal voltage of the transformer and the output in kW when supplying a given load using approximate equivalent circuit when the applied voltage is 7912 V. Your answer
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.