Wastewater Engineering civil engineering (11) A COD test was carried out on a batik factory wastewater. The relevant informationis as follows,Volume of potassium dichromate standard solution (0.1NVolume of wastewater samnpleWastcwater sample dilutionFe2* standard solutionVolume of Fe“" standard solution needed for wastewater sampleVolume of Fe“ standard solution needed for distilled water10.0 mL20.0 mL%3D10X0.1N13.55 mL34.70 mLCalculate the COD value for the batik factory wastewater.

Answered: Image /qna-images/answer/03e746c8-5e09-4836-81f4-67e5ac679076.jpg

A COD test was carried out on a batik factory wastewater. The relevant information is as follows, Volume of potassium dichromate standard solution 0.1N Volume of wastewater sample Wastcwater sample dilution Fe" standard solution Volume of Fe“ standard solution needed for wastewater sample Volume of Fe" standard solution needed for distilled water 10.0 mL %3D 20.0 mL 10X %3| %3D 0.JN 21 13.55 mL 34.70 mL Calculate the COD value for the batik factory wastewater.

A COD test was carried out on a batik factory wastewater. The relevant information is as follows, Volume of potassium dichromate standard solution 0.1N Volume of wastewater sample Wastcwater sample dilution Fe" standard solution Volume of Fe“ standard solution needed for wastewater sample Volume of Fe" standard solution needed for distilled water 10.0 mL %3D 20.0 mL 10X %3| %3D 0.JN 21 13.55 mL 34.70 mL Calculate the COD value for the batik factory wastewater.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A raw sewage sample was brought in for total suspended solids and volatile solids analysis. A portion of the sample was poured into a tared evaporating dish and weighed. The sample was then heated at 105°C for 4 hours, weighed, heated at 550°C overnight, and weighed again. The data are as follows: • Tare wt. 42.9073g• Wt of sample 104.4680g• 105 °C wt. 45.4140g• 550 °C wt. 43.3236g What is the TSS in g/L? What percent of the solids are volatile?
Q3 (a) Describe briefly the main objective water quality and state the mainparameters involved in water quality analysis.(b) Determine the equivalent weight, concentration of each ion in mg/L as CaCO3and total hardness of the following water sample in Table Q3 (b).(c) 50 mL of wastewater sample has been diluted in a 300 mL BOD bottle forBOD5 20°C analysis. Assume that initial DO is 8.8 mg/L, whilst DO at the end of5 days is 4.5 mg/L, calculate the dilution factor (P) and estimate the value ofBOD5 20°C for the wastewater sample.
The specific gravity of particles in wastewater is 2.7 and the kinematic viscosity of water is 1.02x10-2 cm2/s. Compute the required area of tank for removing particles of size 0.07 mm if wastewater is flowing at the rate of 0.2 m3/s in a settling tank.
Q 01: a) What precautions should we follow when conducting experiment in Environmental lab? b) How can you determine chloride content in a waste water sample? Subject: environmental engineering ii lab
02: a)What precautions should we follow when conducting experiment in Environmental lab? b)How can you determine chloride content in a waste water sample? Subject is Environmental Engineering Plz solve it?
Sanitary Engineering Potential of Hydrogen (pH) same question please help me: 1-What are alternative methods for determining the pH of aqueous samples?2- What are typical pH values of drinking water in Jordan? How do your datacompare with these values?3-Discuss the relationship between (a) pH and hydrogen ion concentration (b) pHand hydroxide ion concentration?
The BODs of a domestic wastewater sample is considered to be about 200 mg/l and the DO in it is measured as 0 mg/L. The laboratory staff are preparing to set up a BOD test to determine the actual BOD of the sample. The DO of the dilution water was measured to be 9 mg/I. Which of the following volume ratios of (total volume of BOD bottle = 300 mL) / (volume of wastewater sample) would be most appropriate to use in setting up the BOD bottle for incubation? Select one among the following: (a) 20/1; (b) 50/1; (c) 100/1; (d) 500/1. Justify your selection
A municipal wastewater treatment plant is installing completely mixed activated sludge to meet their NPDES permit of 15 mg/L BOD5. The mixed liquor concentration is 1,000 mg/L MLVSS. The wastewater flowrate going to secondary treatment is 0.170 m3/s and the BOD5 in that stream is 110 mg/L. Laboratory measurements of the growth constants show: Ks = 60 mg/L BOD5, um = 2.8 d-1, kd = 0.05 d-1, Y = 0.73 mg MLVSS/mg BOD5. Determine the required volume of the aeration tank.
A BOD analysis was performed on a municipal wastewater. The 300 mL test bottle was filled with 2.0% wastewater mixed with dillution water, The initial dissolved oxygen (DO) was 8.3 mg/L. The sample is then put in a incubator and set at 20°C. Since the 5th day falls on public holiday, the final DO does not get measured until the 7th day. The final DO is measured at 4.5 mg/L. Assuming k30 (base e) is 0.2/day, determine the BOD3 @ 20°C BOD5 @ 30°C
A waste treatment lagoon having 3 cells, each 115,000 m2 in area, a minimum operating depth of 0.6 m, and a maximum operating depth of 1.5 m, receives 1,900 m3/d of wastewater having an average BOD5 of 122 mg/L. What is the BOD5 loading and detention time? The following data applies: the slope of the lagoon walls is disregarded in the calculations. a. 6.7 kg/ha-d, 54.5 daysb. 20.2 kg/ha-d, 163.4 daysc. 18.5 kg/ha-d, 177.6 daysd. 18.5 kg/ha-d, 54.5 dayse. None of these
The average design flow at a wastewater treatment plant facility is 1.5 m3/s. The bar rack is mechanically cleaned with an average clear spacing of 2.5 cm. Estimate the average quantity of screenings that will be collected at each day.
Sketch a typical treatment process scheme for the treatment of raw water containing a turbidity of 19 NTU, Mn concentration of 0.07 mg/L, Fe concentration of 0.3 mg/L, TOC of 2 mg/L, coliform (#/mL) 800 and color of 18 CU.