A coil has a resistance of 18 N when its mean temperature is 20°C and of 20 Q when its mean temperature is 50°C. Find its mean temperature rise when its resistance is 21 N and the surrounding temperature is 15° C.(pts)

A coil has a resistance of 18 N when its mean temperature is 20°C and of 20 Q when its mean temperature is 50°C. Find its mean temperature rise when its resistance is 21 N and the surrounding temperature is 15° C.(pts)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 500-turn coil is wound on an iron core. When a 120-V-rms 60-Hz voltage is applied to the coil, the current is 1 A rms. Neglect the resistance of the coil. Determine the reluctance of the core. Given that the cross-sectional area of the core is 5 cm2 and the length is 20 cm, determine the relative permeability of the core material.
An 8-pole d.c. machine of 1200kW, 600V, 500 rpm and the average value of the reactance voltage per coil is 6.6V. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bmax/Bav) = 1.5. Find the interpole m.m.f.
7- An 8-pole d.c. machine of 1200kW, 600V, 500 rpm and the average value of the reactance voltage per coil is 6.6V. the machine is lap connected of 648 conductor and each coil has two turns, the axial length of the compole 29 cm and the air gap is 0.8 cm, the armature diameter is 0.35m and the ratio (Bma/B,) = 1.5. Find the interpole m.m.f.
The armature of an 8 -pole dc machine has 72 slots, and its diameter is48 cm. Find the pole pitch in (a) the electrical angle corresponding to a mechanical angle of 350, (b) the mechanical angle corresponding to an electrical angle of 350, and (c) the distances along the armature surface corresponding to the angles in g and h
A cylindrical solenoid is shown in Figure P13.36.The plunger may move freely along its axis. The air gap between the shell and the plunger is uniform andequal to 1 mm, and the diameter d is 25 mm. If theexciting coil carries a current of 7.5 A, find the forceacting on the plunger when x = 2 mm. AssumeN = 200 turns, and neglect the reluctance of the steelshell. Assume lg is negligible.
Suppose a shunt regulator voltage is 250V, the armature current is 30A. field coils are required to provide an MMF of 500AT. The field might typically say 200turns with resistance of 0.5Ohms/turn. Find the dissipated power as heat and total input required and the efficiency
15.1 Consider a wind machine designed to deliver its rated power at the average velocity for a given wind spectrum. It will be marketed for sites having wind velocity spectra that have the same annual average velocity but with Weibull statistics ranging from k = 3/2 to 5/2. a. Calculate the ratio of maximum to minimum annual average on-site wind power available for exploitation for this range of wind fields. b. What additional assumptions are necessary if the power actually produced is to be in the same ratio as in (a) above?
A 4-pole, wave-wound d.c. machine running at 900 r.p.m. has a commutator of 0.46 m diameter. If the armature current is 90 A, thickness of brush 1.25 cm and the self-inductance of each armature coil is 0.08 mH, calculate the average e.m.f. induced in each coil during commutation. Assume linear commutation and neglect mica thickness.
Q23. A PMMC Ammeter has a coil of effective depth of 5 cm and a width of 20 mm, the coil has about 150 turns, and it has coil resistance of 20 ohms. The flux spread in the air gap is done at density of 100mWb / m Then calculate, 1. Control torque produced by the coil, when it measures 15 A. ii. Spring constant, when it measures 15 A and deflects by an angle of 30 ° Deflection torque exerted on the pointer, when it measures 20 A. Analyze the relationship between the area of moving coil and deflection torque produced in a PMMC instrument iv.
A PMMC voltmeter with a resistance of 10 ohms gives has a coil of effective depth of 3 mm and a width of 2.5 cm, the coil has about 100 turns. The flux spread in the air gap is of 10mWb/m2 . The spring has a constant of 2 x 10-6. Then calculate, i. Deflection torque produced by the coil, when it is connected to 20V to measure. ii. Deflection made by the pointer, when the meter is to measure a voltage of 10V. iii. Analyze the reason of fixed the voltage coil in dynamo type wattmeter?
Explain the difference between conductive and inductive compensation
A ferromagnetic ring has a uniform cross-sectional area of 2000 mm2 and a mean circumference of 1000 mm. A hysteresis loop obtained for the specimen is plotted to scales of 10 mm = 0.1 T and 10 mm = 400A/m and is found to have an area of 104 mm2. Determine the hysteresis loss at a frequency of 80 Hz.