Need experts help please , dont provide wrong approach PROBLEM 2A column in a braced building supports a symmetrical arrangement of beams in addition toa vertical load from above, as shown in Figure 6.26. Using the characteristic loadsindicated, check the suitability of a 203 x 203 x 60 UC S 355 section.F:Dead load75 KNImposed load - 175 kNDead loadImposed load = 75 kNFDead loadImposed load= 250 kN= 20 kN= 150 KNFigure 6.26

A column in a braced building supports a symmetrical arrangement of beams in additic a vertical load from above, as shown in Figure 6.26. Using the characteristic 1 indicated, check the suitability of a 203 x 203 x 60 UC S 355 section. F:

A column in a braced building supports a symmetrical arrangement of beams in additic a vertical load from above, as shown in Figure 6.26. Using the characteristic 1 indicated, check the suitability of a 203 x 203 x 60 UC S 355 section. F:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The framing plan of a two-storey reinforced concrete structure is shown below. Due to some issues, the owner suggests to change the corner columns to equivalent circular columns of the same section modulus as the initial square columns designated as shown in the figure. Compute the factors for the distribution of lateral forces per frame. The size of the square columns is 0.50 by 0.50m, girders are 0.3 x 0.5m. Height per level is 3.60 meters. E = 24.84 x 10^6 kPa and G = 9.92 x 10^6 kPA. Use column A-1 as building reference point. Weight at the second level is 1345.23 kN and that of the deck level is 1103.25 kN. The seismic data are as follows: Cv = 0.32Nv, Nv = 1.2, I = 1.0, R=8.5, Ca = 0.32Na, Na = 1.0, Z=0.4. Use 6 decimal places. Analyze frame 1 using Factor Method. Accidental eccentricity is 5% of the total transverse dimension of the structure (24.3m). Use 6 decimal places. Determine the lateral force in the 2nd level (vertical distribution).
The framing plan of a two-storey reinforced concrete structure is shown below. Due to some issues, the owner suggests to change the corner columns to equivalent circular columns of the same section modulus as the initial square columns designated as shown in the figure. Compute the factors for the distribution of lateral forces per frame. The size of the square columns is 0.50 by 0.50m, girders are 0.3 x 0.5m. Height per level is 3.60 meters. E = 24.84 x 10^6 kPa and G = 9.92 x 10^6 kPA. Use column A-1 as building reference point. Weight at the second level is 1345.23 kN and that of the deck level is 1103.25 kN. The seismic data are as follows: Cv = 0.32Nv, Nv = 1.2, I = 1.0, R=8.5, Ca = 0.32Na, Na = 1.0, Z=0.4. Use 6 decimal places. Analyze frame 1 using Factor Method. Accidental eccentricity is 5% of the total transverse dimension of the structure (24.3m). Use 6 decimal places. Determine the stiffness of Frame 1,2,3, & 4 (West to East direction).
25 A 500-mm-diameter, non-slender, spiral column is symmetrically reinforced with six 25 mm vertical bars. Calculate the nominal strength (kN) of this column if subjected to axial load only. Given f’c = 27 MPa and fy = 414 MPa. 4,526 5,657 3,607 4,809
please refer to the example below 1. What is the relative stiffness of span AB, KAB? a. 0.375 I b. 0.125 I c. 2.667 I d. 0.250 I 2. What is the relative stiffness of span BC, KBC? a. 0.250 I b. 0.125 I c. 4.0 I d. 0.375 I 3. What is the distribution factor at point A for span AB, DFA? a. 1.0 b. 0.0 c. 0.6 d. 0.4 4. What is the distribution factor at point B for span AB, DFB1? a. 0.6 b. 0.4 c. 1.0 d. 0.0 5. What is the distribution factor at point B for span BC, DFB2? a. 0.4 b. 0.6 c. 1.0 d. 0.0 6. What is the distribution factor at point C for span BC, DFC? a. 0.0 b. 1.0 c. 0.6 d. 0.4
An 8.5m simply supported beam is subjected with a uniformly distributed load of50KN/m. If the beam is laterally braced at third points and both ends, determine itsunbraced length in meters.
With the following rectangular tied column properties, check the adequacy of the biaxial column. Column Properties: b = 1.20 m h = 0.40 m d' = 0.06 m As = 3080 sq.mm. As' = 3080 sq.mm. Factored Loads: Pu = 1500 kN Mux = 300 kN·m Muy = 300 kN·m f'c = 20 MPa fy = 300 MPa
Given that all main factors remain unchanged, using the Theory of Buckling by Euler’s Formula. What is the ratio (in decimal) of the Modified Column to the Original Column based on the critical buckling load capacity? If a RECTANGULAR STEEL COLUMN is used and assuming that due to architectural requirement, the architect request to makes the column width to half and the column depth remains unchanged?
The given beam carries a distributed load as shown. Determine the resultant force and its line of action. Answers must be R: 609 lb & x:8.16ft
Typical W18 X 55 floor beams of an office building are spaced at 12 feet center to center supporting a superimposed dead load of 90 lb/ft2 and a live load of 50 lb/ft2 . Determine the governing load combination and the corresponding factored load. Calculate the value using the six equations to find out the maximum. Calculate the value using the six equations to find out the maximum. Calculate the value using the six equations to find out the maximum.
Determine the magnitude of force (kN) in member BC if F=75426 N , a=2.91m , b=1.33m and c=5.82m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
1. State five different classifications of loads you know 2. List 3 types of loads 3. With the aid of diagram, list 3 common types of beams based on their support systems. 4. State St. Vennant's principle
A reinforced concrete column with a square cross section of 30 in. × 30 in. , shown in the figure below, is reinforced with 10#9 Grade 60 steel reinforcing bars and #3 Grade 60 steel ties at a center-to-center spacing of 12 in. as shown in the cross section. If the concrete compressive strength is 4000 psi , it is required to calculate the maximum factored concentric force ( ) that can be supported by the column.