(c) A common-emitter amplifier circuit and its voltage transfer characteristic curve are shownin Fig. 1(c). Assume that the transistor common emitter current gain ß = 150 andVBE (on) = 0.7 V. Determine the input voltage at the point X, such that the transistor goesto Vce (sat).Vcc = 12 VVo(V)CutoffVccRc =1.4 k2IcIB+ActiveVceRB=80 k2VBE (on)Vce (sat) =Saturation0.3VV,0 VeE (on) X¼(V)

Answered: Image /qna-images/answer/b7aca90c-ff79-491a-8044-fa4c1c2b19f7.jpg

Answered: A common-emitter amplifier circuit and

Engineering

Electrical Engineering

A common-emitter amplifier circuit and

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Suggest a repair scheme or precautions to be observed while replacing the transistor

A: Switch off the power supply to the circuit board First. Then de-solder the faulty transistor…

Q: Explain how a common collector transistor configuration should be describe. Mention the terminals…

A: n the case of common collector configuration the collector is common whereas the input is base and…

Q: Refer to the figure shown, the collector-base voltage of the transistor if β = 140 is?

A: Given here a electrical circuit and asked to find the collector base voltage.

Q: 4. What are the regions indicated in the output characteristics of the transistor? And For amplifier…

Q: For the transistor circuit shown below, what is the value of the collector current?

A: The required parameter can be calculated by using DC analysis of the amplifier circuit.

Q: Explain the construction and working of the Enhancement MOSFET, with characteristics curve.

Q: How to change the q point of a transistor for a fixed bias configuration without changing the load…

A: Load line: Dc load line is a plot of IC versus VCE for given value of RC at a specific level of VCC…

Q: voltage gain of an emitter-follower configuration of BJT transistor is approximately one. where it…

A: The applications of the voltage follower amplifier are as follows.

Q: Describe the USES OF THE MODIFIED COLLECTOR EQUATIONS ?

Q: Are common-emitter amplifiers inverting or noninverting? What can you say about the magnitudes of…

A: Common emitter amplifiers are inverting in nature. It inverts the signals by 1800. Common emitter…

Q: What parameters determine the stability of a BJT transistor circuit?

A: BJT transistor circuit becomes stable if - Its operating point does not depends upon temperature.…

Q: Figure shows the open circuit failures in a transistor. What will be the circuit behaviour in each…

A: The explanation for all the three cases are as follows.

Q: c. Sketch the input-output characteristics of a transistor connected in common emitter configuration…

A: Input characteristic: It is the curve between base current IB and base-emitter voltage VBE at…

Q: Derive a mathematical expression to determine S(VBE) the stability factor for emitter-stabilized…

Q: Derive a mathematical expression to determine S(β) the stability factor for emitter-stabilized bias…

A: Derive a mathematical expression to determine S(β) the stability factor for emitter-stabilized bias…

Q: voltage gain of an emitter- follower configuration of BJT transistor is approximately one. where it…

A: I have mentioned few points.

Q: Explain the characteristics of the Common Emitter Circuit amplifier.

A: Given : In the common emitter amplifier circuit input will be common for both input and output.…

Q: The insulating layer of in the MOSFET construction, accounts for the very desirable high input…

A: SiO2

Q: In a Bipolar Transistor define the quantity a or hFB. How is the device structure of the npn Bipolar…

A: The quantity alpha is called common base current gain . It's value is always less than unity.

Q: What is the range of β for the transistor?

A: The range of β for the transistor

Q: What is the primary function of a bipolar junction transistor? Briefly discuss you answer.

A: To write the primary function of BJT:

Q: According to the values given in the circuit in the figure, calculate the transistor base current…

A: REGION‌ ‌OF‌ ‌OPERATION‌ ‌OF‌ ‌BJT:‌ ‌ Region‌ ‌of‌ ‌operation‌ ‌ EB‌ ‌Junction‌ ‌ CB‌…

Q: C) Why is the common collector amplifier called an emitter follower? Why is it often used as a…

A: Common collector amplifier called an emitter follower.

Q: Discuss the theory and significance of Common-Emitter Amplifier

A: The common emitter amplifier is one that have input applied between the emitter and the base. The…

Q: What is the operating point (Q-point) of a BJT transistor?

A: BJT is known as a Bipolar Junction Transistor. It is an electronic device. The Q point is basically…

Q: Sketch the DC load line for the voltage divider bias circuit for each transistor case and place the…

A: Diode- When diode become forward bias then it offers very small resistance. It is known as forward…

Q: Ideally. for linear operation a transistor should be biased so that the Q-point is halfway between…

Q: (1) Using a common-emitter transistor configuration circuit discuss une Imput, output and transfer…

Q: How to get Ib, Ic and Beta in this common emitter amplifier?

Q: The dc load line on a family of collector characteristic curves of a transistor shows the

A: In this we will write about dc load line of collector characterestics curves...

Q: When the emitter resistor is bypassed with a capacitor, how is the gain of the amplifier affe What…

A: In this question we will write effect of bypass capacitor across emitter resistance on gain and gain…

Q: Explain DC load line and Q point for any transistor configuration.also state the necessity of…

A: To Explain DC load line and Q point for any transistor configuration.To state the necessity of…

Q: why is the base current in a transistor so much less than the collector current ?

A: The explanation is as follows.

Q: Discuss transistor loadline and operating point

A: Transistor Load line: In the graphical analysis of offline power circuits, the line load line is…

Q: What

A: TRANSISTOR- Transistor is formed by connecting two diodes back to back. This device has three…

Q: In your own words, explain the Channel length modulation effect in MOSFET with a related graph and…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 14. Short-circuit failure mode is associated with microcircuits, transistors, resistors and…

A: A short circuit failure mode causes is also known as steady state failure in this failure the…

Q: Sketch the input-output characteristics of a transistor connected in common emitter configuration…

A: Given Question- Sketch the input-output characteristics of a transistor connected in…

Q: a) In a Bipolar Transistor define the quantity B or hFE- How is the device structure of the npn…

A: Transistor:- It is a semiconductor device that have three terminals. Its main function is switching…

Q: (b) Label the Base, Collector and Emitter in the following figure. What type of transistor is this,…

A: We need to tell name of bjt terminal and type of bjt .

Q: Explain the construction and working of the Depletion MOSFET, with characteristics curve.

A: Depletion type MOSFET Construction N-channel depletion type MOSFET consists of a p-type substrate,…

Q: 4. What is the source of the leakage current in a transistor?

A: Given: What is the source of the leakage current in a transistor?

Q: Conclusion for Common-Emitter Amplifier and AC Analysis

Q: In a Bipolar Transistor define the quantity hFE device structure of the npn Bipolar Transistor…

A: Brief description: In the above given question we need to define & variation of a quantity…

Q: In a BJT common emitter configuration,

A: BJT (bipolar junction transistor)A transistor having a three terminal made up of semiconductor…

Q: What are transistors used for?

Q: 7: Explain constructional features of a MOSFET.

Concept explainers

Power Amplifier

The power amplifier is an electronic amplifier designed to maximize the signal strength of a given input. The input signal strength is enhanced to a high enough level to drive output devices such as speakers, headphones, RF (Radio frequency) transmitters, etc. Unlike voltage / current amplifiers, the power amplifier is designed to drive core loads directly and is used as a storage block in the amplifier series.

Maximum Efficiency Criterion

In every field of engineering, there is a tremendous use of the machine and all those machines are equipped for their popular work efficiency so it very much important for operation engineers to monitor the efficiency of the machine, planning engineers to check out the efficiency of the machine before installing the machine and design engineers to design machine for higher efficiency than and then the utility will procure their products that will ultimately lead to profit and loss of the company. It indicates the importance of efficiency right from the initial stage as manufacturing units, intermediate stage as planning coordinators, and end-users stage as a utility.

Question

(c) A common-emitter amplifier circuit and its voltage transfer characteristic curve are shown
in Fig. 1(c). Assume that the transistor common emitter current gain ß = 150 and
VBE (on) = 0.7 V. Determine the input voltage at the point X, such that the transistor goes
to Vce (sat).
Vcc = 12 V
Vo(V)
Cutoff
Vcc
Rc =
1.4 k2
Ic
IB
+
Active
Vce
RB=
80 k2
VBE (on)
Vce (sat) =
Saturation
0.3V
V,
0 VeE (on) X
¼(V)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the emitter-follower (common- collector) amplifier circuit shown in Fig. 1. determine: (@) Voltage gain, A, = V.V, (b) Current gain. A~ L1, (©) Input impedance, Z, and (d) Output impedance, Z.. Assume that: B = =100, 7e=30Q, and hi = fr. = 3KQ. Hint: Solve the homework and draw the ac equivalent circuit by using 1. or h model.
For the common-emitter amplifier circuit shown in Fig. 1, determine: (a) Voltage gain, A, =V,/V;, (b) Current gain, A;=1/I;, and (c) Inputimpedance, R Assume that: P =hn=1250, r.=20Q, and h;,. = B.r. = 5 kQ. Hint: Solve the homework and draw the ac equivalent circuit by using re or h model.
[16:36, 16.06.2021] Mücahit Sezgin: The common-emitter amplifier given in the figurein the circuit, Vcc=9V, R1=27kΩ, R2=15kΩ,RE=1.2kΩ and RC=2.2kΩ. Transistor β=100has value.[16:36, 16.06.2021] Mücahit Sezgin: a-) If it has values of Rsig=10kΩ and RL=2kΩCalculate the IE of the amplifier. b-) For small signal analysis of transistorFind the value of Rin by deriving the π-model c-) Calculate vo/vsig and io/ii.
For the emitter-follower (common- collector) amplifier circuit shown in Fig. 1, determine: (a) Voltage gain, A, =V,/Vi, (b) Current gain, A; =1/1I; (c) Input impedance, Z;, and (d) Output impedance, Z,. Assume that: B = hg =100, r.=30€Q, and hj. = f.r. = 3kQ. Hint: Solve the homework and draw the ac equivalent circuit by using r or h model.
For the emitter-follower (common- collector) amplifier circuit shown in Fig. 1, determine: (a) Voltage gain, A, = V./V;, (b) Current gain, A; =1,/I; (c) Inputimpedance, Z; and (d) Output impedance, Z,. Assume that: B =hp.=100, re=30Q, and h;e = f.r.=3kQ. Hint: Solve the homework and draw the ac equivalent circuit by using r. or h model.
The common-emitter discrete amplifier shown has the following values: RB1 = 500 kΩ, RB2 = 100 kΩ, RC = 5 kΩ, RE = 200 Ω, Rsig = 1 kΩ, RL = 10 kΩ and VCC = 22 V. Assume VBE = 0.7 V and β = 90. Also assume that the capacitors are shorts for ac. The bias circuit has been analyzed and IC = 2.63 mA, Rin = 0.856 kΩ and Rout = RC. If vsig = 20 mVpeak, determine the peak value of vout.
the emitter-biased small signal amplifier circuit seen.VCC= +20V, RB= 430kΩ, RC= 2kΩ, RE= 1kΩ, RL= 2.2kΩ, C1=C2= 10μF and β= 50.a. Draw the ac equivalent network circuit with re model.b. Find re using Kirchhoff’s current and voltage laws.c. Assume ro=∞ Ω and find Zi, Zo and Av.Assume that a voltage source Vs with an internal resistance Rs of 1kΩ is connected to Vi. Regarding to low frequency response,d. Find the cut-off frequency f1 due to the capacitor C1.e. Find the cut-off frequency f2 due to the capacitor C2 (assume ro=∞ Ω)
A 3-Vrms signal is fed to a transmission line whose attenuation at a certain frequency is 0.002 Neper/meter. The length of the line is 3.5 kilometers and it is terminated using an amplifier whose input and output impedances are equal to the characteristic impedance of the line. The amplifier gain is 110 dB. The output of the amplifier is connected to a similar 3.5-kilometer line. The second line is terminated by its characteristic impedance. Determine the signal voltage at the load of the second line.
For the circuit shown in Fig. 1 below, the transistor parameters are B =150, VBE =0.7V and VT=26mV. a) Determine the operating point parameters. b) Draw the small signal equivalent circuit based on the re mode c) Determine: i Gain of the transistor, Av Input impedance, Za i. Gain with signal, An V. Output voltage, given that V, =30mVSinot
If the circuit of problem 2 is configured as a common-emitter amplifier, calculate the resulting voltage and current gain. Assume a load resistor of 1k ohm. Circuit of problem 2: determine the operating point of a universal trasnsistor DC bias cirucit when Vcc=15V, R1=10k ohm, R2=2.2k ohm, Rc=680 ohm, Re=100 ohm. Assume beta (b)=200 and Vbe=0.72V.
Since Vcc = 25 V, Vi = 31 mV, RB = 470 kΩ, RC = 3.2 kΩ, RE1 = 470 Ω, RE2 = 1.2 kΩ, RL = 40.5 kΩ and β = 110 in the circuit in the figure, the output voltage (Vo Find the value of ). NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: The output impedance (r0) of the transistor will be neglected.
ı just need the fınal answer Since Vcc = 20 V, RS = 3 kΩ, RB = 380 kΩ, RC = 1.2 kΩ, RE = 2.2 kΩ, RL = 911 Ω and β = 90 in the circuit in the figure, find the value of the output voltage (Vo). NOTE-1: It is within the 1 kHz mid-band frequency and the capacitors are negligible at this frequency. NOTE-2: The output impedance (r0) of the transistor will be neglected. a. 64,14 mV b. 83,88 mV c. 93,75 mV d. 74,01 mV e. 103,62 mV f. 24,67 mV g. 34,54 mV h. 49,34 mV