A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that: E-200GN/m² E=70 GN/m² and a=11×10 per °C and a=22×10 per °C for Steel for Aluminum Alloy

A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that: E-200GN/m² E=70 GN/m² and a=11×10 per °C and a=22×10 per °C for Steel for Aluminum Alloy

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
A 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 kN. Poisson’s Ratio = 0.25 and E = 200 000 MPa. Compute the lateral strain. Express your answers in 6 decimal places.
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. where P=25 .
rectangular steel plate, 1·2 m long and 850 mm wide, is subject to a compressive load along its length. If the width of the plate increases by 0·09 mm under load, determine its change in length. Take Poisson’s ratio for the steel as 0·28
1.2 A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner diameter is 0.18m. The rod is compressed axially with a load of 200kN. The modulus of elasticity and the Poisson's ratio of the rod are 200GPa and 0.3 respectively. Determine the increase in outside diameter of rod using the calculated value of decrease in length. (The decrease in length=0.17mm)
A steel pipe of length L =7.0 ft, outside diameter d2 = 6.0 in., and inside diameter d1 = 4.5 in. is compressed by an axial force P 140 kN. The material has modulus of elasticity E = 30,000 ksi and Poisson's ratio v = 0.30. Determine the following quantities for the pipe: (a) the shortening (delta) (b) the lateral strain E' , (c) the increase Ad2 in the outer diameter and the increase Ad1 in the inner diameter, and (d) the increase At in the wall thickness.
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.8 GPa. Bar (2) is a nylon material that has an elastic modulus of 1.9 GPa. Each bar has a cross-sectional area of 900 mm2. Using L = 395 mm and Δ = 4.6 mm, what magnitude of load P will cause the normal stress in each bar to be the same value?