A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 60 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 86 MPa. If a torque of Tc=26800 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = mm d₂ = mm (2) (1) B

A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 60 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 86 MPa. If a torque of Tc=26800 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = mm d₂ = mm (2) (1) B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The shaft is made from a solid steel section AB and a tubular portion made of steel having a brass core. It is fixed at a rigid support at A and a torque T=50lb-ft is applied at C. Gsteel= 11,500 ksi Gbrass= 5,600 ksi What is the angle of twist at C? What is the maximum shear stress in the steel and brass? What is the maximum shear strain in the steel and brass?
A solid steel shaft ABC of 50mm diameter is driven at A by a motor that transmits +50kW to the shaft at 10Hz. The gears at B and C drive the machinery using power equal to -35kW and -15kW, respectively. Determine the maximum shear stress in the shaft & compute the angle of twist of the shaft between the motor at Ao and the gear at C. Please take note: the values are negative (-35 & -15) & G = 83 GPa
A solid steel shaft ABC of 50mm diameter is driven at A by a motor that transmits +50kW to the shaft at 10Hz. The gears at B and C drive the machinery using power equal to -35kW and -15kW, respectively. Determine the maximum shear stress in the shaft & compute the angle of twist of the shaft between the motor at Ao and the gear at C. Please take note: the values are negative (-35 & -15)
The shaft has a square-threaded screw with a lead of 8 mm and a mean radius of 15 mm. If it is in contact with a plate gear having a mean radius of 30 mm, determine the resisting torque M on the plate gear which can be overcome if a torque of 7 N ⋅ m is applied to the shaft. The coefficient of static friction at the screw is μB = 0.2. Neglect friction of the bearings located at A and B.
A set of 5-lb forces are applied to the handles of the pliers as shown. Simple pinconnections exist at pts. B, C, D, and E. Determine the compressive force developed on thesmooth cylinder at pt. A.
A helical spring is fabricated by wrapping wire ¾ in. indiameter around a forming cylinder 8 in. in diameter. Compute thenumber of turns required to permit an elongation of 4 in withoutexceeding a shearing stress of 18 ksi. Use 12,000,000 psi formodulus of rigidity.
The stepped shaft ACB shown in Figure bellow is fixed at both ends and loaded by a torque TO at point C. Segment AC having solid circular cross section and segment CB having hollow circular cross section. If the shafts material is steel with shear modulus G = 11 x 10°psi, and the torque is To = 8,000 lb-in. Calculate: (a) The maximum and the minimum shear stress in segment CB. (b) The maximum and the minimum shear strain in segment CB. (c) The angle of rotation 0, at the cross section where the torque To is applied.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.
A hollow bronze shaft of 75mm outer diameter and 50mm inner diameter is sleep over a solid steel shaft 50mm in diameter and of the same length as the hollow shaft. The two shells are then fastened rigidly together at their ends. Determine the maximum shearing stress developed in each material by end torques of 3 KN-m. For bronze G=35GN/m2 and for steel G=83GN/m2. Answers should be in MPa.
The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation (in degrees) of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Answer in 1 decimal place
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
If couple forces of F = 10 lb are applied perpendicular to the lever of the clamp at A and B, determine the clamping force on the boards. The single square-threaded screw of the clamp has a mean diameter of 1 in. and a lead of 0.25 in. The coefficient of static friction is μs = 0.3.