A compressed tank contains water at 70 °C and unknown pressure. If the tank volume is 0.6 m3 and the total mass of water inside the tank is 0.1 kg. What is the phase of water inside the tank? Question 7 options: superheated vapor phase saturated liquid-vapor mixture (i.e. 2 phases inside) compressed liquid phase critical point (i.e. can't distinguish between the liquid and vapor) saturated vapor phase saturated liquid phase

A compressed tank contains water at 70 °C and unknown pressure. If the tank volume is 0.6 m3 and the total mass of water inside the tank is 0.1 kg. What is the phase of water inside the tank? Question 7 options: superheated vapor phase saturated liquid-vapor mixture (i.e. 2 phases inside) compressed liquid phase critical point (i.e. can't distinguish between the liquid and vapor) saturated vapor phase saturated liquid phase

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter11: Calibrating Instruments

Section: Chapter Questions

Problem 4RQ: Temperature-measuring instruments may be designed to measure the temperature of vapors, ________,...

See similar textbooks

Similar questions

A bicycle tire with a volume of 0.00212 m3is filled to its recommended absolute pressure of 495 kPa on a coldwinter day when the tire’s temperature is −15 °C. The cyclist thenbrings his bicycle into a hot laundry room at 32 °C. (a) If the tirewarms up while its volume remains constant, will the pressureincrease be greater than, less than, or equal to the manufacturer’sstated 10% overpressure limit? (b) Find the absolute pressure inthe tire when it warms to 32 °C at constant volume.
ASAP Pls dont round off initial values, round off final ans only ty The pressure 24 meter below a liquid is 786.41 kPa, determine its mass density (kg/m³).
At 86 degrees Fahrenheit (°F) and 111.83 psi absolute, R-134a boils (itchanges from a liquid to a gas). One pound of liquid R-134a occupies0.0135 cu ft of volume. When it changes to a gas, it requires 0.4132 cu ftmore space. What volume will 1 pound of R-134a occupy as a gas at 86°Fand 111.83 psi?
A gas is initially at 0 gage pressure and compressed to 1/4 of the initial volume at constant temperature. What is the new gage pressure?(include units with answer)
I've posted the below question earlier, and I received the answer. This is the question: A J-shaped tube is filled with air at 760 Torr and 22 °C. The long arm is closed off at the top and is 100.0 cm long; the short arm is 40.00 cm high. Mercury is poured through a funnel into the open end. When the mercury spills over the top of the short arm, what is the pressure on the trapped air? Let h be the length of mercury in the long arm. I need further explanation of one step: - when P2 is obtained in the short arm, the equation is 40-h+P1 1. How did we get this equation? 2. the short arm does not contain any air, why do we create an equation of P2 in the short arm? Please clarify these concerns.
What is the phase and pressure of water at 280°C with specific volume 0.92 m3/kg? answer : superheated vapour, 0.2866 MPa Explain how it came
A 6-m³ tank contains helium at 400 K and is evacuated from atmospheric pressure to a pressure of 740 mm Hg vacuum. Determine (a) mass of helium remaining in the tank, (b) mass of helium pumped out, (e) the temperature of the remaining helium falls to 10°C. What is the pressure in kPa?
How can we analyze a spherical pressure vessel?
A 6m3 tank contains helium at 127C and is evacuated from atmospheric pressure to a pressure of 730 mm Hg Vacuum. Determine the mass of helium remaining in the tank. MW of Helium is 4kgm/kgmol
When does boiling occur in a fluid? Briefly state Pascal's Law?
Complete the blank cells in the following table of properties of water
A rigid tank containssome liquid water at 300C. The rest of the tank is filled with atmospheric air. Is it possible to boil the water in the tank without raising its temperature? How? Draw a schematic diagram,andthen plot the state/s and process, whichever is applicable in a t-sdiagram