a) Compute the depth of compression block   and b) the ultimate moment capacity of the beam shown in Figure 2.   Assume fy=28MPa    and fy=414MPa

Q: Situation

A:

Q: ted loads W,V & A, det

A:

Q: If there is settlement of S at the support C, solve the slope at B using slope deflection method

A:

Q: A compound curve is composed of 3 and 5 degree curves with I1 = 22 degree and I2=30 degree, respecti...

A:

Q: 3) A centrifugal pump delivers water between two reservoirs with a 300 ft. elevation difference (Az)...

A: Apply Bernoulli’s equation between reservoir 1 to reservoir 2 as follows:  ……. (1) Here,  is the pre...

Q: Using Moment distribution method. Find Distribution Factor of joint E and joint B

A: We have to determine the value of distribution factor as per the moment distribution method of joint...

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel [E...

A: Given data -

Q: A concrete column 285 mm in diameter is designed to carry an axial compressive load of 388.526KN. De...

A:

Q: Using MDM for the continuous beam below, determine the following structural parameters and support m...

A: As there are multiple questions posted, according to the guidelines, only the first three are being ...

Q: The bearing pad consists of a 150 mm by 150 mm block of aluminum that supports a compressive load of...

A:

Q: Hagen-Poiseuille equation; (2) Darcy-Weisbach equation;

A:

Q: Determine the force in members KJ, JN,ND and C D.

A: Given data-

Q: Problem: A vertical triangular gate with a top base horizontal and 1.5 m wide is 3m high. It is subm...

A:

Q: Question 3. For the truss shown below, determine the forces in all members caused by the applied loa...

A:

Q: Data of a closed traverse are as follows: Compute the distance of line (5-1) a. 206.92 m b. 374.97 m...

A: Let distance 3-4 be x and distance 5-1 be y 

Q: 6. For the beam shown, determine the following: A. moment of inertia of the section B. absolute maxi...

A:

Q: Explanation

A: Steel has good damping properties so not prone to vibration issues.  Creating curved sections of ste...

Q: Propose THREE (3) strategies for the control of volatile organic compounds (VOCS) in indoor air.

A: Volatile organic compounds (VOCs) are the chemicals which are found in various products which are us...

Q: A truck with axle loads shown rolls across a 10-m span. What is the maximum bending moment and maxim...

A: For the given rolling loads across a 10m span, the maximum shear and bending moment have to be compu...

Q: Consider the following figure of a barrage: 120 m 102 m 16 m 4 m! 25 m The exit gradient of the barr...

A:

Q: Situation

A:

Q: 10. Design and draft a pedestrian refuge with two curb ramps according to Caltrans standards. Add ca...

A: Medians or refuge islands make a two-stage crossing for walkers, making it simpler and more secure t...

Q: The common tangent BC of a reversed curve with a common radius is 280.5 and has azimuth of 312deg 29...

A:

Q: n the given cable carrying a horizontal uniform load of 7.5 KN/m, and point C is the lowest point in...

A:   Cable: - It is a flexible structure that support transverse loads by developing tensile resistanc...

Q: Assuming that the beam has the cross section shown: 1.) Draw shear and moment diagrams using area me...

A:  

Q: At a conference, after everyone had shaken hands with everyone else, it was found that 45 hand shake...

A: Given, At a conference, after everyone had shaken hands with everyone. Then 45 handshakes were excha...

Q: The soil fraction that get sieved through 0.075 mm sieve is more than 50% of the total weight of soi...

A:

Q: k = 0.2 m/s b = 24.5 m h1 = 47.4 m h2 = 24.1 m x = 891.2 m length of aquifer is 1756.6 m 3. calculat...

A: step 1-

Q: 26. A soil element is shown in Fig 25. Determine the following: a. Maximum and minimum principal str...

A: We will use basic formula.

Q: Slope Deflection Method nstructions: Solve the following problems completely using Slope Deflection ...

A:

Q: An equal tangent vertical curve connects a 1% and 3% initial and final grade. Design speed is 70mi/h...

A: Given that -

Q: Calculate the increase in stress for each segment of the compound bar shown. If the temperature incr...

A: As per the given information we need to calculate the we need to find out the increase in the stress...

Q: A culvert has an expected life of 40 years and is designed for a flood magnitude of rank 3 out of th...

A:

Q: Situation. A simply supported one way RC slab has a 3 m span. It carries a serv

A:

Q: For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spa...

A:

Q: kPa, what is the maxim to exceed 40 kPa?

A:

Q: Determine all reactions in the given beam. Draw the shear & moment diagram for the beam.

A:

Q: Curves Problem: 1+12 For the given compound curve (see figure): a. Determine R, and R2. b. Determine...

A:

Q: Problem 7: In the following system determine the internal force in spring 1. Rigid 2k 3k

A: Given - 

Q: A beam with a channel section is subjected to a bending moment M having its vector at an angle e to ...

A:

Q: 225 P= 8 P= 10 9,- 18 Rg 2 (m) 1 (m) 4.50 (m) 1.50 (m)

A:

Q: An instrument is set up at point A sighted a rod at a certain distance and recorded a stadia interce...

A:

Q: (a) Draw three co entire beam, a section cut (2)

A:

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum...

A: Given -

Q: Determine all reactions in the given beam. Draw the shear & moment diagram for the beam. USING MOMEN...

A:

Q: Determine the maximum moment, in kN-m, on the beam

A:

Q: Čonsider the following figure of a barrage: 120 m 102 m 16 m 4 m! 25 m The exit gradient of the barr...

A:

Q: H |B 40 kN 40 kN - 4 at 3 m = 12 m -

A:

Q: The shrinkage limit of a clay is 22%, its natural moisture content is 34.7%, and its specific gravit...

A:

Q: Determine the reactions in pin A, B, C and D. 0.5 m 1.5 m 0.75 m 2.25 m 1.5 m 3 m 0.5m 0.75 m 500 N

A: