A concrete dam given in the figure haswater 13 m deep acting on its verticalsides. The coefficient of friction betweenthe soil and the dam is 0.60.-23.5. How far in meters isYconcretem³the vertical resultant force from the toe?a = 15 mb= 13 m2mab2m2m15m

Answered: Image /qna-images/answer/cd573e4f-7d2a-4f06-98e5-e036e80a2636.jpg

A concrete dam given in the figure has water 13 m deep acting on its vertical sides. The coefficient of friction between the soil and the dam is 0.60. Yconcrete = 23.5. How far in meters is the vertical resultant force from the toe? a = 15 m b= 13 m 2m a b 2m 2m 15m

A concrete dam given in the figure has water 13 m deep acting on its vertical sides. The coefficient of friction between the soil and the dam is 0.60. Yconcrete = 23.5. How far in meters is the vertical resultant force from the toe? a = 15 m b= 13 m 2m a b 2m 2m 15m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Related questions

Q: Q1/ Draw the distribution of the effective stress for section A-A in the following soil profile: A…

A: Given, Soil profile diagram Load = 150 kN

Q: Problem (8.3): Derive the equation of the deflection curve for a simple beam AB loaded by a couple…

Q: A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress…

Q: Draw BMD for the following 20KN 1 Вс SFD and BMD for the Boom Diagram. 10kN/m

Q: An aluminum block (SG=2.5) has a dimension of 0.24 m x 0.24 m xh meters. It is floating in mercury…

Q: If If a point load acting at the mid span of a fixed beam of uniform section produces fixed end…

Q: 14 kN B DO F H 6 m E G 2 m 2 m 2 m

Q: up to a depth of 13 ft from the ground and below which lies sand. The clay stratum is saturated…

A: Given:- depth=6.5ft w=30 percent Gs=2.72 Sandy stratum,w=26 percent Gs=2.64 To find;- total pressure…

Q: answer in 4 decimal places please

A: Given A simply supported beam Required Draw the shear-force and bending-moment diagrams for the…

Q: Q.2- Answer with true and false, and correct false statements. EVENTE U from the int increasin. 3-…

A: Part 4 Minimum concrete cover thickness depends on the exposure environmental conditions and…

Q: The answer should be in Nm

A: State the largest bending moment to be applied safely in N-m rounded to three decimal places

Q: SITUATION 10: Water is flowing at a depth of 1.5 m in a 3 m wide rectangular channel having n=0.013…

Q: D —3f3ft E 2 ft F W

Q: 3. A pump draws water at 300 liters per second from reservoir A and lifts it to reservoir B as…

Q: Determine the foreces in the members marked by “x” in the truss loaded as shown at the right. Use…

A: This question is related to the structure analysis.

Q: a section 2.07 m from A if P = 5470 N. W=2372 N/m, a = 1.2 m, b = final answer to two decimal…

Q: A W360X110 is used as a 7.3 m - long column with pinned end supports. The column is laterally…

Q: The beam has a 20 Mpa concrete, dimensions of b=400mm, d=550 mm and reinforced with 4-25 mm diamter…

Q: a. Determine the final velocity of both beads. b. Determine the average interaction force, F between…

Q: width (8 m) and grade line for the road is lateral inclination is 1:1. The distance between the…

Q: GIVEN: f(x) = cos(x)-√4-x² Using NEWTON'S METHOD, determine new estimate after 2nd iteration. ε =…

A: Asked: To determine the root of the given function after second iteration using Newton's formula.…

Q: Two designs for a beam are to be considered. Determined which one will support the loading shown…

Q: Determine the foreces in the members marked by “x” in the truss loaded as shown belwo. Use method of…

Q: Please define the term of anisotropy and bending stiffness.

A: anisotropy, in physics, the quality of exhibiting properties with different values when measured…

Q: Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: For soil profile shown in figure below, estimate the consolidation settlement due to pla 3m fill…

Q: A saturated sample of normally consolidated clay was consolidated under an all-round cell pressure…

A: Cu = qu2 where qu - compression strength Cu - shear strength we have,…

Q: A third-point loading flexural (bending) test was performed on a concrete beam with a cross section…

Q: te for the m

Q: Mechanics of Materials 2nd Class Dr. Luma Fadhil Sec.: C Q: Draw the shear force and bending moment…

A: Given data:

Q: The pump shown in the figure draws water from Reservoir A and discharges the fluid into a nozzle at…

Q: =hown in the figure. The distributed load includin of intensity 244 lb/ft over

A: Given:- udl=244lb/ft span=19.3ft b=4in Est/Ewd=20 To find:- maximum bending stress

Q: S 0 Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter,…

Q: What is civil engineering

A: Civil engineering is, without a doubt, the most ancient engineering subject. It is concerned with…

Q: At what angle should a highway curve of 610-ft diameter be banked to accommodate cars travelling at…

Q: T 2 m + 2 m 2 m A B -2 m2 C DE F m2 m2 m2 m----2 m- 10 kN 10 kN Q-2 Q-2: Determine the force in each…

Q: The quantity of Fine aggregate required in making cement concrete of quantity 15 m³ using mix 1 :…

A: given volume of the concret mix=15 m3ratio of the mix=1:1.5:2.5

Q: Q1/ Draw the distribution of the effective stress for section A-A in the following soil profile: A…

Q: A Class I two-lane highway has a b m, and shoulder width is 2.4 m. T roadway is located in rolling…

A: Given data - Free -flow speed =110 km/h Lane width - 3.6m % of bucks =0.01 % of Ryz PR =0.05…

Q: Determine the consolidation settlement for the foundation shown in the figure below. The so profile…

Q: PROBLEM 7 Determine the coordinates of the centroid of the shape given below. y 0.8 m 0.6 m 1.0 m

A: A shape is given as shown in the figure above and it has been asked in the question to determine the…

Q: Consider a standard flexural strength specimen of length L, width a, and depth a. Assume center…

Q: shown in figure (2). Draw the shear-force and bending-moment diagrams for this beam.

Q: For the system shown start from rest. Neglect all frictional forces, which of the following…

Q: Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

A: Given Data; discharge time = 5mins mass = 3.5kn

Q: 120 kN/m El -5m

A: Only part 1 question is solved using slope deflection method. Since it is not possible to solve all…

Q: A composite bar made up of aluminum and steel is held between two supports as shown. The bars are…

Q: mpany has delivered an annual quantity of 120,000,000 m3 (including leakage) to a city of 1.2…

A: Given: annual quantity = 120,000,000 m3 (including leakage) to a city of 1.2 million inhabitants…

Q: (3) Use Virtual Work to determine slopes at A, B and C, and the displacement at C. Check all results…

A: As per policy, only one question can be answered. For solution using the moment area method kindly…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: Given data Allowable bending stress = 12 MPa d = 200 mm

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

A concrete dam given in the figure has
water 13 m deep acting on its vertical
sides. The coefficient of friction between
the soil and the dam is 0.60.
-
23.5. How far in meters is
Yconcrete
m³
the vertical resultant force from the toe?
a = 15 m
b= 13 m
2m
a
b
2m
2m
15m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
An open tank 3m by 3m in horizontal section weighs 4 kN and contains water to a depth of 1m. It is acted by an unbalanced force of 18 kN parallel to the pair of sides. a) Determine the acceleration of the tank. b) What must be the height of the tank so that no water will spill out? c) If the acceleration is increase by 4m/s2 , how much water will spill out?
A dam is inclined at an angle of 30\deg from the vertical and has the shape of an isosceles trapezoid 80 ft wide at the top and 40 ft wide at the bottom and with a slant height of 60 ft. Find the hydrostatic force on the dam when the water level is at the top of the dam. (Round your answer to the nearest whole number. Assume that the weight density of this water is 62.5 lb/ft3.)
If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance below the liquid surface, determine the depth to its center of pressure. What is the horizontal force acting on the triangle? Assume ? water = 9790 N/m3. f = depth to apex, 2m d = height of triangle, 1m a = width of triangle, 1m The horizontal force (N) acting on the triangle is:
A dam with specific weight of 24 kN/m3, has dimensions of 6m on top, 20m at the bottom and 27m high has water 22m deep acting on its vertical side. Compute the location of the vertical resultant force from the toe. 8.01 10.81 1.80 18.10
A concrete dam given in the figure has water 35 m deep acting on its vertical sides. The coefficient of friction between the soil and the dam is 0.60. Yconcrete 23.5. How far in meters is the vertical resultant force from the toe? a-28m b-25m
An underground conical tank, standing on its vertex, is being filled with water at the rate of 18pi ft3/min. If the tanks has a height of 30feet and a radius of 15feet, how fast is the water level rising when the water is 12 feet deep? a. 3/4 ft/min b. 1/4 ft/min c. 1/2 ft/min d. 1/3 ft/min
A 65 cm cube weighing 2.5KN is lowered in a tank containing 1.50 m of water below 1.20 m of oil of specific gravity 0.82. If the sides of the cube remain vertical: a. How much of the cube projects above the oil-water interface? b. What is the total hydrostatic force acting on the side of the cube?
A concrete cube ( y = 23.5 kN/m3 ) 0.60 m on an edge is submerged in 5 m of seawater (sg=1.03). Calculate the force to lift the cube if there is no seepage pressure at the bottom of the cube A. 23.3 kN B. 28.5 C. 27.7 D. 26.9
3. The 500 mm diameter pipe conveys treated water to supply a municipality with a demand of 40 MLD. Determine the head loss in meter if the length of the pipe is 10 km considering that (a) friction factor f is 0.018, (b) Hazen-William coefficient C is 90, and (c) Mannings coefficient n is 0.015.
High velocity water flows up an inclined plane, as shown in Figure 5 .1 What are the two possible depth of flow at section 2? Neglect al losses.
What height of a column of a special gage liquid (sp. gr. = 2.95) exert the same pressure as a column of oil 4.5 meters high (sp.gr. = 1.19)? a. 1.58 m b. 1.28 m c. 1.85 m d. 1.82 m