A concrete dam given in the figure has water 21.22 m deep acting on its vertical sides. Assuming that the hydrostatic uplift varies linearly from one-half the hydrostatic head at the upstream side edge to zero at the downstream edge of the dam. The coefficient of friction between the soil and the dam is 0.60. Yconcrete = 23.5 How far in meters is the vertical resultant force from the toe? 5m 3m 20m 15 m

A concrete dam given in the figure has water 21.22 m deep acting on its vertical sides. Assuming that the hydrostatic uplift varies linearly from one-half the hydrostatic head at the upstream side edge to zero at the downstream edge of the dam. The coefficient of friction between the soil and the dam is 0.60. Yconcrete = 23.5 How far in meters is the vertical resultant force from the toe? 5m 3m 20m 15 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete dam is triangular in cross section and (30+0.314)m high from the horizontal base. If water reaches a depth of (27+0.314)m on the vertical face, what is the minimum length of the base of the dam such that the resultant will intersect the base within the middle third? What minimum coefficient of friction is required to prevent sliding ? Determine the pressure distribution along the base. If the uplift pressure varies from half full hydrostatic at the heel to zero at the toe.
Given Figure E1, draw the active earth pressure distribution. Use gw = 9.81 kN/m3. Determine the magnitude and location of the active thrust.
A masonry dam (sp.gr. = 2.4) of trapezoidal cross-section is 20 m high. It has a thickness of 2 m at the top and 14 m at the bottomas shown in the figure.Coef. of friction under the foundation is 0.80 and assuming there is hydrostatic upliftthat varies linearly from one-half the hydrostatic head at the upstream edgeof the dam to zero at the downstream edge.Determine
A vertical triangular plate whose height is 3.6 meters has its base horizontal and vertex upper most in the water surface. a. Find the depth to which it must be lowered from its vertex so that the difference in level between the center of gravity and the center of pressure shall be 20cm. b. How far is the center of pressure below the water surface? c.What is the base width of the plate if the total hydrostatic force acting on the plate is 76.28 kN?
A concrete dam retaining water is shown in the figure. If the specific weight of the concrete is 23.5 kN/m3, Find the factor of safety against overturning. Assume there is no hydrostatic uplift, and that the coefficient of friction between the dam and foundation soil is 0.48. Find the factor of safety against sliding. Assume there is hydrostatic uplift that varies from full head at the heel to zero at the toe, and that the coefficient of friction between the dam and foundation soil is 0.58. Find the minimum pressure intensity on the base. Assume there is no hydrostatic uplift, and that the coefficient of friction between the dam and foundation soil is 0.48. Find the maximum pressure intensity on the base. Assume there is no hydrostatic uplift, and that the coefficient of friction between the dam and foundation soil is 0.48.
A gravity dam in the figure carries water that is 12 m deep on its upstream side. The coefficient of friction between the soil and the dam is 0.50. γ_concrete=23.5 kN/m^3 a. How far is the vertical resultant force from the toe? b. What is the factor of safety against sliding? c. What is the factor of safety against overturning? d. What is the soil pressure in heel? e. What is the soil pressure in toe?
If the total passive thrust is 200 kN/m2 and total active thrust is 500 kN/m2, then determine the safe friction force required to prevent sliding.
Referring to the basic concepts for studying lateral earth pressures, calculate the magnitude of lateral force resulting from an active soil pressure against the back of a frictionless wall 6 m high. The surface behind the wall is level, with the retained soil having an angle of internal friction equal to 37° and a unit weight of 18 kN/m3.
A concrete dam is going to be built on a silty/clayey sand stratum overlaying an impermeable bedrock as shown in figure below to provide a water reservoir. What is the uplift pressure in point 2? A. 22.2kPA B.27.2KPa C.29.2kPA
5. What is the factor of safety against overturning for the triangular dam? Determine the pressure distribution at the base of the dam. Neglect hydrostatic uplift. Use unit weight of concrete 24kN/m³.
A concrete dam retaining water is shown. If the specific weight of the concrete is 23.54 kN/m3, find the maximum pressure on the base. Assume there is no hydrostatic uplift and that the coefficient of friction between dam and foundation soil is 0.48. Y = 5.6 m B = 3.2 m W = 1.6 h = 4.8
Please be detailed and clear with your solution. Figure shows a semi-conical buttress. Calculate the total hydrostatic force acting on the surface of this semi-conical buttress.