, A concrete pile is 20 m long and has a cross section of 0.46 m × 0.46 m. The pile is embedded in a sand having y = 17 kN/m³ and d' = 38°. The allowable working load is 1200 kN. If 700 kN are contributed by the frictional resistance and 500 kN are from the point load, determine the elastic settlement of the pile. Given: E, = 2.1 × 106 kN/m², E, = µ, = 30 X 10³ kN/m², 0.38, and g = 0.57

, A concrete pile is 20 m long and has a cross section of 0.46 m × 0.46 m. The pile is embedded in a sand having y = 17 kN/m³ and d' = 38°. The allowable working load is 1200 kN. If 700 kN are contributed by the frictional resistance and 500 kN are from the point load, determine the elastic settlement of the pile. Given: E, = 2.1 × 106 kN/m², E, = µ, = 30 X 10³ kN/m², 0.38, and g = 0.57

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Similar questions

A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Qp by a. Meyerhofs method b. Vesics method c. Coyle and Castellos method Use m = 600 in Eq. (12.28).
A concrete pile is 18 m long and has a cross-section of 0.406 m x 0.406 m. The pile is embedded in the sand having γ = 16 kN/m3 and Φ' = 370. The allowable working load is 900 kN. If 600 kN are contributed by the frictional resistance and 300 kN are from the point load, determine the elastic settlement of the pile. Given: EP = 2.1 x 106 kN/m2 , ES = 30 x 103 kN/m2 , μS = 0.38, and ξ = 0.57.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2 and ?s = 0.2.
Determine the ultimate load capacity of a circular pile with diameter D = 20 cm installed in asaturated soft clay. The pile is embedded 10 m into the ground. According to measurements, thesoil exhibits an undrained shear strength according to the linear relationship: Su = 2+1.6z, wherez is the depth in meters and Su is the undrained shear strength in kPa. The soil's unit weight canbe assumed as 18 kN/m3
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
A square prestressed concrete pile with a cross section 0.3 m by 0.3 m is driven 15 m into overconsolidated clays with properties as defined: From the ground surface to a depth of 7 m, the unit weight is 17 kN/m3 and the shear strength cohesion cu is 70 kPa; below 7 m, the soil unit weight is 18.5 kN/m3 and cohesion is 105 kPa. Use the total stress α-method to calculate both the design downward axial capacity and upward axial capacity, using a factor of safety of 3 (downward and upward).
The wooden pile shown in the figure has a diameter of 100 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 4.99 kN/m. The length of the pile is L = 4.2 m and its elastic modulus is E = 8.7 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
Consider a 15 m long concrete pile with a cross section of 0.45 m x 0.45 m fully embedded in sand.For the sand, unit weight, γ = 17 kN/m3 and soil friction angle, ϕ’ = 35o. Estimate the ultimate point??? with each of the following:1.1 Meyerhof’s method (Ans: 1014 kN)1.2 Vesic’s method (Ans: 1754 kN)1.3 Coyle and Castello’s method (Ans: 2479 kN)
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
An excavation 5 m depth is supported by a sheet pile. The sheet pile is extended 3.2 m below the ground and the water table is at the bottom of the pile. Unit weight of soil is 1.91 g/cc. Angle friction is 34°. 1. Which of the following most nearly gives the active force? a. 178.3 kN b. 133.73 kN c. 205.05 kN d. 151.56 kN 2. Which of the following most nearly gives the passive force? a. 274.9 kN b. 308.84 kN c. 339.38 kN d. 397.07 kN 3. Which of the following most nearly gives the passive resistance to mobilize stability? a. 388.2 kN b. 456.7 kN c. 548.04 kN d. 502.37 kN