A conductor with a specific gravity of 40.10-3 kg/m.mm2 was drawn between two poles, which are given in the figure and erected on a valley slope, with a tension of 10 kg/mm2. Accordingly, find the conductor stress at the high suspension point.   Please answer in short i will like and dont reject please its urgent...

Q: The frame shown in the figure is supported by a pin at A and a roller at F. Pins connect members at…

A:

Q: A uniform cylinder is supported by a rigid bar AB ang cable BC as shown in the figure. If the stress…

A: Givenallowable stress in the cable σa=7.25ksi=7250 psidiameter of the cable, d=0.50in

Q: A bar of circular cross section is to suspend a tank of water 4 ft. below a ceiling. The tank can be…

A:

Q: Figure Q2 shows that state of stress at a point within a loaded body consists of a combination of…

A:

Q: Q3\ for the vessel pressure shown in fig find longitudinal and hoop tensile stress in the wall…

A: The given data are: P=3 MPaR=2 mt=4 mm=0.004 mL=3 m Here, P denotes the internal pressure, R denotes…

Q: A COMPRESSED AIR TANK HAVING ÄN INNER DIAMETER OF 450 mm AND A WALL THICKNESS OF Ce.25 mm Is FORMED…

A: Given d=450mmt=6.25mm

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

A:

Q: Q5- The gate in Figure below is 5 ft wide, is hinged at point B, and rests against a smooth wall at…

A:

Q: Calculate the combined stress (MPa) on the rod shown below using principle stress method. Here, F1 =…

A: Different forces creates different effects at the fixed end Force F1 creates direct normal tensile…

Q: In the figure below, a crane is supported by two cables of cross-sectional area equal to 3.04 cm2.…

A:

Q: Home Work :- A hydraulic cylinder as show in the figure is subjected to a compressive force (F) at…

A:

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

A: To given thatElectric power transmission pole is above ground level=12mEmbedded into the ground…

Q: The small piston of a hydraulic lift (see figure below) has a cross-sectional area of 2.70 cm?, and…

A: Given:Cross-sectional area of small piston, a=2.70 cm2Cross-sectional area of large piston, A=203…

Q: The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The naximum longitudinal…

A:

Q: A 4.20 m long (L) steel pipe has a mass of 450 kg and is lifted by a crane attached to cable CD.…

A:

Q: A structure, which cross-section is S= 100 mm², is submitted to a tension of 1kN. What is the…

A:

Q: The tank shown in the figure is fabricated from 10 mm steel plate. Determine the maximum…

A: Solution   Calculate the circumferential stress          σc=pd2t=1.2×0.62×0.01=36 MPa

Q: A girder shown in the following figure is supported by two cables. The weight of the girder is 8000…

A: For the given girder  Weight of girder (W) = 8000 lb    To determine  The tension in both cable and…

Q: Show the derivation of the girth and longitudinal stresses of the thin-walled cylindrical container…

A: Given: INTERNAL PRESSURE=P, INSIDE DIAMETER=d WALL THICKNESS=t Stress=σ length of section=l   at the…

Q: Show the derivation of the girth and longitudinal stresses of the thin-walled cylindrical container…

A:

Q: The tank shown in the figure is fabricated from 10 mm steel plate. determine the maximum…

A: Solution   Calculate the circumferential stress                 σc=pd2t=1.2×0.62×0.01=36 MPa

Q: . For an 8-ft length of gate in the figure, find the compression in strut CD due to water pressure…

A:

Q: A hydraulic system is used to apply a force in an external fixation device to hold broken ends. The…

A: Given data: P=3 MN/m2D=30 cmd=4 cmL=2 mE=200 GN/m2 Need to determine the stress in the piston rod…

Q: Question cm is subject to 4 forces of 1 kN each applied at the edges of the plate with a 45-degree…

A: First of all we have to resolve these forces along x and y axes. The inclined forces then becomes…

Q: A thin cylindrical pressure vessel of 1.2 m diameter generates steam at a pressure of 1.75 N/mm2.…

A: Given data:

Q: figure and

A: hang is characterized as contrast between the level between the places and absolute bottom of the…

Q: A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the…

A:

Q: Q4: An inclined circular gate (AB) with hinge support at (B) and the weight of gate (12KN).…

A:

Q: The state of stress at a point, for a body in place stress, is shown in the figure below. If the…

A:

Q: A closed thin walled cylindrical vessel has a diameter D of 100 mm, a wall thickness t of 8 mm and…

A:

Q: shown below. Sa

A:

Q: A triangular dam is shown in the figure, base is 6-m and height is 8-m. Compute for the factor of…

A:

Q: Twó immovable concrete blocks are connected with a 2 inch by 2 inch square bar. At 72°F there is no…

A:

Q: 1. For an 8-ft length of gate in the figure, find the compression in strut CD due to water pressure…

A:

Q: A thin walled spherical shell is subjected to an internal pressure.If the radius of the shell is…

A: Given:Thickness is reduced by 1%shell diameter is increased by 1%

Q: In the system in the figure, two rods carry the P force. a) Since the maximum stress that the rods…

A:

Q: 3. The rail roads are usually made of steel material segments with a 10 m long. Between each…

A:

Q: A retaining wall 6 ft high is constructed ofhorizontal wood planks 2.5 in. thick (actual…

A: a draw the free body diagram    here h = 6 ft is the length of the span s is the thickness of the…

Q: A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is…

A: Given data, External diameter, do = 250 mm Thickness of the cylinder, t = 5 mm Internal diameter of…

Q: to applied force P = 10 kN. For simplicity, assume AE = 1 for all members. 4 m 4 m 4 m

A:

Q: The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The maximum longitudinal…

A:

Q: QI/ for the vessel pressure shown in fig find longitudinal and hoop tensile stress in the wall…

A: Longitudinal Stress, σL = 250 MPa. Hoop Stress, σH = 500 MPa.

Q: Question 1 cm is subject to 4 forces of 1 kN each applied at the edges of the plate with a 45-degree…

A:

Q: Find the stress acting on the surface of a thin sphere of diameter 15 cm, thickness 0.25 cm and the…

A: From the given question, Diameter of the sphere = d = 15 cm Thickness of the sphere = t = 0.25 cm…

Q: As figure show are depicts the cross-section of a closed-end cylinder with an internal diameter of…

A:

Q: Q2 A steel bar of cross-sectional area 200 mm2 is loaded as shown in Fig. Find the change in length…

A:

Q: The tank shown in the figure is fabricated from 10 mm steel plate. Determine the maximum…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.