A conical vessel is 12 m across the top and 15 m deep. If it contains water to a depth of 10 m, find the work done in pumping the liquid to a height of 3 m above the top of the vessel. O 17258.25 kJ 43136.77 kJ 37445.11 kJ 20802.84 kJ

A conical vessel is 12 m across the top and 15 m deep. If it contains water to a depth of 10 m, find the work done in pumping the liquid to a height of 3 m above the top of the vessel. O 17258.25 kJ 43136.77 kJ 37445.11 kJ 20802.84 kJ

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2 kN 45° Find the vertical deflection at point C for the frame shown below using the unit load…

Q: Water flows over a flat plate at a free stream velocity of 0.20 m/s. There is no pressure gradient…

Q: Air at 1 atm and 20 C flows in a 2-cm-diameter tube. The maximum velocity (m/s) of air to keep the…

A: Reynolds numbers : In various fluid flow scenarios, the Reynolds number aids in the prediction of…

Q: 1. Is there a difference between the values of Qideal Calculated by equation (1) and Qat using…

A: Note: As per guidelines for multiple questions only one question can be answered. So for other…

Q: The "Approval" step of the Typical Project Sequence provides an opportunity for which of the…

A: Project Seequencing refers to the process that need employees to accomplish activities in a…

Q: The ionic character of a groundwater is defined by the following hypothetical combinations: = 0.4…

A: given-Mg(HCO3)2=0.4 meq/LCa(HCO3)2=3.0 meq/LMgSO4=0.8 meq/LNaCl=0.6 meq/LNa2SO4=0.2 meq/L

Q: For the given beam below bent about the horizontal axis of its cross section. Solve for fbtMAX &…

A: ASKED: To draw the shear and moment diagram of the beam, and compute the maximum tensile and…

Q: A,f, 107.4 mm 0.85/,'b Ca/B =107.4 mm / 0.85

A: Given data,

Q: S KN /m

Q: 1.7.2 Plot load vs.penetration graph and determine the in-situ CBR value for this layer. Calibration…

A: Given data:

Q: The soil layers below have a cross-sectional area of 100 mm x 100 mm each. The permeability of each…

Q: rigure Q3 shows the cross section of an existing road in a flat rural area. a) Briefly explain the…

Q: a) Determine the preload and service load stresses in the bolt. Compare to the SAE minimum proof…

Q: Determine the design flood discharge (allowing an increase of one third) for a bridge site with the…

A: Given: The catchment area is 2 x 105 ha. The duration of the storm is 8 hr. The storm precipitation…

Q: he horizontal and vertical components of

Q: Problem 3 Solve the scheduling data for the following project and compute the relevant information…

A: Precedence Diagram: From the given data the diagram can be drawn as below Here…

Q: A builtup steel beam comprise of two flange plates 250 mm wide × 10 mm thick and web plate 330 mm…

Q: The maximum diameter that a capillary tube can have to ensure that a capillary rise of atleast 6 mm…

A: given-capillary rise h=6 mmsurface tension T=0.08 N/mdensity ρ=900 kg/m3

Q: A prismatic steel beam is shown in the figure

Q: In the table below are the calculations of the total and average cost of an engineering equipment…

Q: Datermine the horizontal and vertical components of reaction at the supports. Neglect the thickness…

A: Length of simply supported beam, L=6mThe external loads are 5KN, 4KNtension in rope.The left end…

Q: EXERCISES 4:Find the tangent line at the given point 1. xy = -4, (2, –2)

A: Given: xy = -4 and point = (2,-2)

Q: BC, CH, HI, and CI. (Ans: load @ H: NBC = -1.78, P16.45 NCH = 0.56) %3D A E H. -16 ft 16 ft 16 ft16…

A: ASKED: To compute the force in members BC, CH, HI and CI. Given, load is placed at H.

Q: B. Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and…

Q: Calculate the force acting on ABC, BD, and 3 ft 6.5 ft DP 3 ft CDE. Draw B FBD 6.5 ft 6 ft E 5 ft

Q: Construct the third projection of the prism and complete the other two projections of point A, B, C…

A: Answer:-

Q: The total unit weight of the glacial outwash soil is 16 kN/m3. The specific gravity of the solid…

Q: For the truss shown in Figure 2: (Take, A- 30 mm and E- 200 Gpa for all members) 1 Find the…

A: As per company's guidelines we can only answer first question. Kindly post other questions as…

Q: the ed quantities for a uniform dead load of 1.5 klf, a moving uniform blems 16.33 through 16.39, us…

Q: 6. Discussion: 1. Is there a difference between the values of Qideal calculated by equation (1) and…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: Find: Using the Principle of Virtual Work, calculate the vertical deflection of Point E, and the…

Q: from the shear stresses data above, DRAW THE SHEAR STRESS DISTRIBUTION DIAGRAM at each point of the…

Q: Draw top view only

A: in this question one isometric projections are given and we are asked to draw top view only

Q: What are the steps in the Qualification-Based Selection (QBS) Procedure?

A: There are different types of selections procedures for the procurement. There are some decided…

Q: The dimensions of a symmetrical welded section are shown in the figure.

Q: For formation of collapse mechanism in the following figure, the minimum value of P, is cM,/L. M, &…

Q: What is the importance of knowing the material specification in plumbing design?

A: Any type of building like residential or commercial or industrial, can't function properly without…

Q: In the triangle ABC segment DE is parallel to that of AC. Determine the length of AC when AD=7,…

A: Given- Triangle ABC-DE is parallel to ACAD=7DB=2DE=3

Q: olve for the reactions and draw the shear and moment diagrams of the following beams using both…

Q: e of 5 m³/s. What is the gross his hydro resource and what night be considered?

A: Given data: 1.Gross head = 100m. 2.Flow rate = 5 m^3/s 3.Assuming efficiency Francis turbine…

Q: What is the difference between a contract and an agreement?

A: Answer:-

Q: Given the Frame as shown below with "mm" unit for length. Using Method of Members, determine the…

Q: A continuous beam is loaded as shown in the figure below. ASsuming a plastic moment capacity equal…

A: Considering span HI and applying Virtual work method ; We get ; Mp θ + 2 Mp θ = P y Mp θ + 2 Mp θ =…

Q: cube container is completely filled with water and weighed 245KN. Compute the length of a side of a…

Q: SPEED Assuming the pavement condition and cross section remain constant. The terrain is also…

A: Solution: From the given terrain plan calculate the design speed for the each curve: at Point C, D,…

Q: Solve by FDM with two Dirichlet BCs. d²v El wx?

Q: Une énd and supported on linear elastic springs (both having a rigid beam Is ninged #ness of 'K') at…

Q: The maximum diameter that a capillary tube can have to ensure that a capillary rise of atleast 6 mm…

Q: A saturated clay has a water content of 39.3% and a bulk specific gravity of 1.84. Determine the dry…

A: w=39.3% w=39.3/100 w=0.393 Bulk specific gravity=1.84 Bulk specific weight= 1.84×10=18.4 KN/m3 Dry…

Q: Q31. A trapezoidal channel with bottom width of 4.0 m and side slopes 1:1 has Manning's N of 0.02.…

Question

A conical vessel is 12 m across the top and 15 m deep. If it contains water to a depth of 10 m,
find the work done in pumping the liquid to a height of 3 m above the top of the vessel.
O 17258.25 kJ
43136.77 kJ
37445.11 kJ
20802.84 kJ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Interior finishes for wood light frame construction

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

an open rectangular tank mounted on atruck is 8 m long and 1 m. wide. it is filled with water to a depth of 3.69 meters. if it is accelerated at 10.16 m/s^2 along its length, determine the required height (in meters) of the tank to prevent any water from spiling.
An open cylindrical vessel 1.20m in diameter and 2.10m high is 2/3 full of water. If the vessel is rotated about its vertical axis at a constant speed of 90rpm, compute:The height of the paraboloid the water at a constant speed of 90rpm rotation.
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
An underground conical tank, standing on its vertex, is being filled with water at the rate of 18pi ft3/min. If the tanks has a height of 30feet and a radius of 15feet, how fast is the water level rising when the water is 12 feet deep? a. 3/4 ft/min b. 1/4 ft/min c. 1/2 ft/min d. 1/3 ft/min
An open rectangular tank is 4m long, 2m wide and 2m high kounted on a truck full of waterm Calculate the volume of water spilled out when the truck from the rest accelerated 2.45 m/s^2
A 1.5 m diameter vertical cylindrical tank 3 m high contains 2.5 m of water. A 100 mm diameter circular sharp-edged orifice is located at its bottom. Assume c=0.6, how long will it take to lower the water level to 1 m deep after opening the orifice?
A tank with a horizontal sectional area constant at 10m2 and 4m high contains water to a depth of3.5m. The tank has a circular orifice 5 cm in diameter and located at its side 0.5m above the bottom.If the coefficient of discharge of the orifice is 0.60, find the duration of flow through the orifice.
A cylindrical vessel 1.20 m in diameter and 2 m high has a rounded circular orifice 5 cm in diameter in the bottom with C = 0.95. If the vessel is full of water, how long will it take to lower the surface 1.50 m?
1. Compute the head loss in a pipe with diameter 300 mm for a length of 15,000 meters and carrying a flow of 0.097, if f=0.02. (Hint: Use h=(0.0826fL(Q^2))/(D^5)
A square tank 1.20m on each side,3m deep is filled to a depth of 2.70m with water. A WOODEN CUBE having a specifix gravity of 0.5 measuring 60 cm on an edge is placed in the water so that it will float. A.) Determine the weight of the water displaced by the cube Choices: 2.12 kN,1.06kN,1.15kN,2.30kN B.)Determine the rise of water above the original liquid surface Choices: 0.15m,0.088m,0.075m,0.30m C.) Determine the change in pressure force on one side of the tank Choices: 2.84kN,2.55kN,2.42kN,2.75Kn
In Figure W is shown a thin-walled inverted box 1.60 m long and 30 cm square, which was full of air before being submerged. In position (a), it is being held by 0.0280 m3of concrete anchor weighing 23540 N/m3. Determine the depth D1. At what other depth D2(position B) is the system in equilibrium?
A rectangular scow 9 m wide, 15 m long, and 3.6 m high has a draft in sea water of 2.4 m. Its center of gravity is 2.7 m above the bottom of the scow. a. Determine the final metacentric height b. If the scow tilted until one end is just submerged in water, find the sidewise shifting of the center of buoyancy. Unit of the Correct Answer: meter Decimal Places required in the final answer: 4