A convolutional encoder has single shift register with two stages three modulo-2 adders and an output multiplexer. The following generator sequences are combined by the multiplexer to produce the encoder output g₁ = 1 0 1 and g₂ = 110. a) Draw the encoder. b) For the message sequence m= 100 1 1, determine the encoded sequence. c) Draw the state and Trellis diagram for this code.

A convolutional encoder has single shift register with two stages three modulo-2 adders and an output multiplexer. The following generator sequences are combined by the multiplexer to produce the encoder output g₁ = 1 0 1 and g₂ = 110. a) Draw the encoder. b) For the message sequence m= 100 1 1, determine the encoded sequence. c) Draw the state and Trellis diagram for this code.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
Please try this question It's is digital signal processing question
Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F= YO Y Y, Y, D. Y. Decoder O a. B' O b. C O'c.B O d. C
a Multiplexer : a) can only have one Se lector Switch b) routes or Connects the Se lected data input to the output c) Selects the least bits and rouks to output d) routes or connects the Seleced outpot from the input data
Adocs.google.com is a logic switch that select information from one of the input line and directs it to a single line Encoder Decoder Adder Multiplexer Binary to octal can be implemented used 3-8 De-Multiplexer Multiplexer Decoder Encoder System base 12 include numbers from ... to .... 1-B 1-C 1-12 1-11 ۹:۰۳ F
convert the data 101110001100 into digital signal using line coding ( DICODE NRZ).
A multiplexer has 3 select lines and two enables. How many other inputs are there? How many TOTAL inputs are there? How many output/outputs are there? Draw a block diagram of this multiplexer.
Your task is to implement a Full Adder Using TWO 4:1 Multiplexers but this time connect Cin and Y to the Select Inputs of the Multiplexers,and connect 1’s, 0’s, X, or X’ to each Data Input.
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
4. The following Data input and data select waveforms are applied to a Multiplexer. Determine the output waveform. Do D Dy So
Procedure: You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The arithmetic unit takes as inputs two 4-bit numbers (A and B) and one control input (M) add/subtract selector that selects the type of operation the unit will perform. When the input control is ‘0’, the input numbers are added. When it is set to ‘1’, the two input numbers are subtracted (A - B). Question: Two 4-bit Adder/Subtractor Circuit: Design and construct a 4-bit adder/subtractor circuit. Draw the produced circuit.
5) -31 is represented as a sign Binary number ( using Sign-magnitude form ) equal to (A) 00011111 (B) 10101001 (C) 01110010 (D) 00101101