A crude diving board is made by nailing two metric-sized wood boards together as shown in Figure P9-98. Compute the deflection at the end if the diver exerts a force of 1.80 kN at the end. The wood is Grade No. 2 southern pine. 1.8 kN RA 2.0 m 2.8 m 1.0 m-1.0 m- B B A A 290 90x290 wood beam Section A-A Ra 290 90x290 wood beam 45x290 wood beam Section B-B 90 Dimensions in mm 90 45 t 135

A crude diving board is made by nailing two metric-sized wood boards together as shown in Figure P9-98. Compute the deflection at the end if the diver exerts a force of 1.80 kN at the end. The wood is Grade No. 2 southern pine. 1.8 kN RA 2.0 m 2.8 m 1.0 m-1.0 m- B B A A 290 90x290 wood beam Section A-A Ra 290 90x290 wood beam 45x290 wood beam Section B-B 90 Dimensions in mm 90 45 t 135

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The simply supported wood beam is loaded as shown. Ewood=10 GPa What is the slope at A? What is the deflection at C?
A simply supported beam carrying floor joist shown in Figure is made of rectangular wood having a dimension of 50mm x 100mm. Compute the maximumdeflection if E = 8.47 x 10^3MPa (for guijo, stress grade 80).
Determine the maximum deflection of the simply supported beam. The beam is made of wood having a modulus of elasticity of E = 1.5 (103) ksi.
Reaction forece SFD & BMD Location and size of maximum deflection.
Determine the ff. unknowns on the beam shown using CONJUGATE BEAM METHOD. Consider 250 mm x 250 mm section and E= 200 Gpa. Computer for: a.) Deflection at point B in mm b.) Maximum deflection on the beam in mm Dont forget that the given values are: a= 6.5 m b= 38 kN-m c= 15 kN Provide complete solution. PLS ANSWER ASAP. I'LL RATE, THANKS
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER A simply supported beam 2.40m span is subjected to a central point load of 15 kN. Take El for the beam section as 6x1010 N-mm2 Determine the maximum slope of the beam at its center. a. 0.07 rad b. 0.09 rad c. 0.11 rad d. 0.05 rad Determine the maximum deflection of the beam at its center. a. 2.70 mm b. 7.02 mm c. 0.72 mm d. 7.20 mm
Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the coefficient of static friction is 0.25 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges.
A cantilever beam 5 m long carries a concentrated load P at 3.75 m from the fixed end. ( E = 25 x 103 MPa, I = 1.6 x 109 mm4, P = 150 KN) What is the deflection under the load P? What is the maximum beam deflection? What is the upward force applied at the free end to prevent the beam from deflecting?
SURVEYING A 50m tape weighing 0.143slug has a standard pull of 5.5kg. The tape’s cross-sectional area and modulus of elasticity are 0.03cm^2 and 200GPa, respectively. What pull, in kg, is required in order that the effect of sag will be eliminated when the tape is supported at end points only.
Given a cantilever beam, determine theslope and deflection at point A. EI isconstant. Answer: θ = 1250/EI kN/m2 counterclockwise;Δ = -10,000/EI kN/m3 upward Need solution please
In the figure shown, each of the four vertical links connecting the two rigid horizontal members is made of aluminum (E = 70 GPa) and has a uniform rectangular cross section of 10 x 40 mm. For the loading shown, determine the deflection and the direction of (a) point E, (b) point F, (c) point G?
Flexure beam.