A cylinder coil with a round bar magnet is given N = 100 turns. the magnetic field is homogeneous and edge effects are negligible:Given values:1= 30 cmd= 3 cmN = 100H = 1000He= 4tha 10 th VsAt theI = 0.9 AdDetermine the following four sizes inside the coil:1) magnetic field strength H. enter the result in the positive x-direction for online submission e, at.ChooseAnswer:2) magnetic flux density B., enter the result in the positive x-direction for online submission e, at.Answer:Choose.

According to question: 1) The magnetic field intensity 'H' along positive 'x' axis is calculated as…

A cylinder coil with a round bar magnet is given N - 100 turns. the magnetic field is homogeneous and edge effects are negligible: Given values: I- 30 cm d= 3 cm N. 100 H.- 1000 Me- 4thr 10 h V Atthe L= 0.9 A

A cylinder coil with a round bar magnet is given N - 100 turns. the magnetic field is homogeneous and edge effects are negligible: Given values: I- 30 cm d= 3 cm N. 100 H.- 1000 Me- 4thr 10 h V Atthe L= 0.9 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. A magnetic circuit consists of a toroidal silicon sheet steel with relative permeability ?? of150, and a small air gap.A current ? flows through 200 turns of wire wrapped around the toroid.The magnetic flux of the circuit is 5 × 10−9 ??. The total length of the circuit is 0.8 m, and thecross-sectional area of the toroid is10−4?2. The length of the air gap is 0.07 m. Findi. the total reluctance and inductance of the circuitii. magnetomotive force and hence the current.?0 = 4? × 10−7?/M
A coil has N=25 turns. The toroid on which the coil is wound has ID=5 cm and OD = 5.5 cm. The geometryresults in a mean path length of 0.165 meters and a cross sectional area of 4.91 micrometer squared. What equation is used for calculating the field strength (also called intensity) H along the mean-path length within the toroid? Calculate the Reluctance in the path of flux lines if Mr is 500.What is the resulting Inductance?
Two coils that are separated by a distance equal to their radius and that carry equal currents such that their axial fields add are called Helmholtz coils. People in science and industry use coils like this to make regions where the net magnetic fields are relatively uniform (but not perfectly uniform). Let R=0.12 cm, I=22 A, and N=320 turns for each coil. Place one coil in the y-z plane with its center at the origin and the other in a parallel plane at R=0.12 cm. Calculate the resultant field Bx at x1=0.03 cm, x2=0.06 cm, x3=0.08 cm, and x4=0.12 cm. For my answers I got B1 = .00416 T, B2 = .00353 T, B3 = .00306 T, and B4 = .00221 T all of which were wrong. Can you please help me?
A loop of wire is bent to have straight and circular arc shaped parts as shown in the figure. A constantcurrent I of 36A flows through the wire in the direction depicted in the figure. If the length R equals13 cm, determine the magnitude and the direction of the magnetic field produced by the loop of wireat point O by using Biot-Savart’s Law (µ0=≈1.26x10-6 T.m/A)
An infinitely-long, hollow, conducting cylinder carries a uniform current I that flows parallel to its axis and into the paper. Its inner radius is a and its outer radius is b. Derive expressions for the magnetic field for (a) a < r < b and (b) r > b Note: See image for the figure.
L:26) A permanent magnet that is infinitely long in the direction perpendicular to its height t, is made a cylindrical hole of radius R. Finds the magnetic field in all space when R << t. Hint: Consider the system as the union of the magnet without the hole plus a magnetization cylinder opposite to the magnet.
The magnetic field intensity in a magnetic material in the form of a circular rod with magnetic permeability n with its axis in the z direction is azH0(H0 is constant). 1)what's B and M inside the bar? What are the equivalent magnetizing current densities jmv and jm for the magnetized rod?
Two ideal solenoids of radii R and 4⁢R , respectively, have n turns per meter, and each carries a current of I. Both currents flow in the same direction. The small‑radius solenoid is placed inside the large-radius solenoid so that their axes of symmetry are parallel and separated by a distance d=2⁢R . Neglecting any magnetic screening effects, express the magnetic field strength on the axis of the small-radius solenoid analytically in terms of the quantities given and the magnetic permeability of a vacuum, μ0 .
Using the Biot-Savart law, find the magnetic field at point P that produces the circuit shown in the figure, where the curved parts correspond to a quarter circle of radii a and b, with steady current I.
A long, cylindrical wire has the cross-section of an annulus, i.e. region between twoconcentric circles, see the shaded area in figure a). The outer radius of the wire is 2R, the innerdiameter is R. Current I flows along the wire (perpendicularly into the page) in uniform distributionbetween radii R and 2R. 1)Find and plot the magnitude of the magnetic field as a function of distance r from thesymmetry axis of the wire.2) Suppose now that the cavity of radius R is not coaxial with the outer surface of the wire, asseen in figure b). Find the magnetic field at point P located in the center of the cavity. The currentdistribution in the wire is assumed to be uniform, the value of current is I.
Calculate the value of emf generated in a cylindrical coil of radius of 5 cm and a height of 10 cm, which is rotating at 1500 rev/sec in a uniform magnetic field of 4500 Gauss. The coil is wound of 5000 turns.
1. In inductive circuit is carrying a current of 4A. If its inductance is 0.15H, find the value of the self induced emf when the current is reduced to zero is 0.01 s. 2. A horse shoe magnet has two poles, each of area 5 cm². Find the pull between the poles and the keeper when the flux density at the contact surface is 1 Wb/m2?