A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm respectively shrunk on to an inner tube of internal and external diameters 8 cm and 16.01 cm respectively. The internal pressure developed in the cylinder is 300 MPa. If E= 200 GPa, find the maximum hoop stress developed in each tube.

A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm respectively shrunk on to an inner tube of internal and external diameters 8 cm and 16.01 cm respectively. The internal pressure developed in the cylinder is 300 MPa. If E= 200 GPa, find the maximum hoop stress developed in each tube.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.13P: A plain concrete wall (i.e., a wall with no steel reinforcement) rests on a secure foundation and...

See similar textbooks

Similar questions

A plain concrete wall (i.e., a wall with no steel reinforcement) rests on a secure foundation and serves as a small dam on a creek (see figure). The height of the wall is h = 6.0 ft and the thickness of the wall is t = 1.0 ft. Determine the maximum tensile and compressive stresses o*!and trt, respectively, at the base of the wall when the water level reaches the top {d = h). Assume plain concrete has weight density ye= 145 lb/ft . Determine the maximum permissible depth dnuxof the water if there is to be no tension in the concrete.
The gas tank consists of a cylindrical section with two hemispherical endcaps. The cylinder has a diameter of 75 cm and a wall thickness of 2 cm. If the allowable circumferential stress is 150 MPa and longitudinal stress is 100 MPa, find the maximum allowable internal pressure in the tank. Answer: P = ___________________
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
An axial pull of 40000 N is acting on a bar consisting of three sections of length 30 cm, 25 cm and 20 cm and of diameters 2 cm, 4 cm and 5 cm respectively. If the Young’s modulus = 2 × 105 N/mm2, determine : (i) stress in each section and (ii) total extension of the bar.
A thick cylinder internal diameter 240mm external diameter 240mminternal diameter ‘D’ is subject to external pressure of 40MPa. Determine the diameter‘D’ if the minimum hoop stress in the cylinder is not to exceed 200MPa in mm.
The inner diameter of the AB compressed air tank is 160mm, the wall thickness is 1mm.Since the manometer pressure in the tank is 1,6MPa ,at point a at the top of the tank maximum normal stress and determine the maximum plane shear stress.(c=16mm , d=38mm, e =32mm, g=160mm, h=1mm, k =1.6MPa , F=160N)
The tank shown in the figure is fabricated from 10 mm steel plate. Determine themaximum longitudinal and circumferential stress caused by an internal pressure of 1.2MPa.
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flatbands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa
A steel tube 3.2 cm in internal diameter, 0.25 cm thick and 4 meters long is coveredand lined throughout with copper tubes 0.20 can thick, 7he three tubes are finnlyattached to each other and united at their ends. This compound tube is subjected to axial tension and the stress produced in the steel tube is60 N/mm2. Determine(a) the elongatio~i of the tube(b) the stress in the copper tubes and(c) the load carried by the combined tube.Efor steel = 2.1 x 16 N/mm2 and,E for Copper = 1.1 x 1 o5 N/mm2
A rubber bolt is inflated to apressure of 65kPa. At that pressure, te diameter ofthe ball is 240mm and the wall thickness is 1.25mm. The rubber has a modulus ofElasticity = 3.7 MPa and Poisson’s ratio v=0.48. Determine the maximum stress in theball if its stress is half that of the cylinder.
A 1.5-m-diameter cylindrical tank is formed of 6-mm-thick sheet steel (E = 200 Gpa, ν = 0.3). The maximum shear strain occurring in this tank when the contents pressure is 1 MPa, is:
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm