A)- Determine the line currents and phase voltages. *Determine the lamp resistances by Ohm's Law, calculate the 25 W 25 W capacitive reactance and use these to predict the phase voltages. Draw a R. phasor diagram to illustrate this. 2 Nominal lamp resistances: Supply voltage OV VP 25 W 40 W 60 W 4.4 Q 46 Q 64.4 0 6.9 O 30 68.5 0 97.4 0 31.8 0 42.9 Q *Average Vp= 27.20 Average VL= 47.106 VL 3.

A)- Determine the line currents and phase voltages. Determine the lamp resistances by Ohm's Law, calculate the 25 W 25 W capacitive reactance and use these to predict the phase voltages. Draw a R. phasor diagram to illustrate this. 2 Nominal lamp resistances: Supply voltage OV VP 25 W 40 W 60 W 4.4 Q 46 Q 64.4 0 6.9 O 30 68.5 0 97.4 0 31.8 0 42.9 Q Average Vp= 27.20 Average VL= 47.106 VL 3.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Illustrate the phasor diagram of the phase and line voltage of the given data below.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Design a quarter wave matching section if the line has a characteristic impedance of 100 ohm while the load Is a 300 ohm resistor. Specify the length of the matching section if the velocity factor is 0.90 at a frequency of 150 MHz.
Estimate the distance over which a load of 15000 KW at p.f-0.8 lagging can be delivered by a 3-phase T.L having conductor each of resistance 0.8 2 per km the voltage at the receiving end is to be 132 KV and the losses in the line is to be 5% of received power
1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3. and find the value of the maximum average power transferred to.
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
Using a test equipment, Vmax was found to be 5V while Vmin is 1V. The distance between voltage maximas is 14 cm and the first maximum was found to be 7 cm from the load. What is the load impedance if the characteristic impedance of the line is 75 ohms?
A three-phase 60-Hz transmission line has its conductors arranged in a triangular formationso that two of the distances between conductors are 25 ft. and the third distance is 42 ft.The conductors are ACSR Osprey. Determine the inductance and inductive reactance perphase per mile.
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance