(a) Determine the reactions at A and E if P = 840 N. The reactions are positive if to the right or up, negative if to the left or down. (b) What is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads. 3.6 m Answers: Ax= qua Ay = Ex= (a) If P = 840 N. A E i i tel Pmax = i 4.4 m B 29, 3630 N D 4.4 m N N N (b) The maximum value which P may have for static equilibrium: N

(a) Determine the reactions at A and E if P = 840 N. The reactions are positive if to the right or up, negative if to the left or down. (b) What is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads. 3.6 m Answers: Ax= qua Ay = Ex= (a) If P = 840 N. A E i i tel Pmax = i 4.4 m B 29, 3630 N D 4.4 m N N N (b) The maximum value which P may have for static equilibrium: N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.59P: The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the...

See similar textbooks

Similar questions

The uniform bar AB of weight W and length L is pinned to a sliding collar at A and to the sliding rod BD at B. The spring wound around rod BD has a stiffness k and is undeformed when rod AB is in the position =0. Determine the expression for the angle (other than =90 ) at equilibrium and investigate the stability of equilibrium for this position.
A slender homogeneous bar is bent into a right angle and placed on a cylindrical surface. Determine the range of b/R for which the equilibrium position shown is stable.
The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k, and the spring is unstretched when =80. If W=kL, the bar has three equilibrium positions in the range 0, only one of which is stable. Determine the angle at the stable equilibrium position.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
Find the equilibrium positions of the 30-lb homogeneous bar and investigate their stability.
What is Equilibrium of a Rigid Body? Give an example.
Based on the figure below, derive the equilibrium equations, in terms of tension, shown below:
The upper end of the bar of a problem is now leaned against a non vertical wall. Determine the minimum value of the angle θ for which equilibrium is possible for μs = 0.25 and for μs = 0.50
When F = 300 N with Θ = 40°, what is the maximum value which P may have for static equilibrium? Neglect the weight of the structure compared with the applied loads.
A straight, uniform bar weighing 60lb rests in a horizontal positon between two frictionless slopes. A concentrated load of 200lb acts at distance x from the right hand slope. Determine x and reaction forces assuming that the bar is in static equilibrium.
Q)Two blocks A=150 N and B=? are connected by a rod at their ends by frictionless hinges as shown in the Fig. Find the weight of block B required for limiting equilibrium of the system, if µ = 0.35 at all sliding surfaces.
review engineering statics Take d1 = 600 mm, d2 = 800 mm, θθ = 45° and F = 500 N (a) Show that member DB is a two-force member? Draw a qualitatively correct extended free-body diagram of DB. (b) Draw an extended FBD of member ABC. (c) Write the three equilibrium equations for member ABC (namely Fnet, x = 0, Fnet,y = 0, and Mnet/P,z = 0). Make clear the choice of your point P for the moment equation. (d) Find the forces acting on member ABC at A and B (give your answer in component form or as a direction and magnitude.) Show your work. These are my answers FBD=2F, RAX=353.5N RAy= 353.5N but am not sure if a correct any help