A differential leveling loop began on BM Rock (elevation=938.08 ft) and closed on BM Tree (elevation=942.47). The plus sight and minus sight distances were kept approximately equal. Readings (in feet) listed in the order taken are 5.8 (+S) on BM Rock, 4.35 (-S) and 3.5 (+S) on TP1, 3.25 (-S) and 6.33 (+S) on BM X, 5.22 (-S) and 4.45 (+S) on TP2, and 3.24 (-S) on BM Tree. Prepare, check, and adjust the notes. (Tabulate your answer)

A differential leveling loop began on BM Rock (elevation=938.08 ft) and closed on BM Tree (elevation=942.47). The plus sight and minus sight distances were kept approximately equal. Readings (in feet) listed in the order taken are 5.8 (+S) on BM Rock, 4.35 (-S) and 3.5 (+S) on TP1, 3.25 (-S) and 6.33 (+S) on BM X, 5.22 (-S) and 4.45 (+S) on TP2, and 3.24 (-S) on BM Tree. Prepare, check, and adjust the notes. (Tabulate your answer)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Reduce the set of differential leveling notes in Table 2-11, and perform the arithmetic check. -Adjust the elevation of BM K110. The length of the level run was 780 m, with setups that are equally spaced. The elevation of BM 132 is 187.536 m.
- In reciprocal leveling across a deep ravine the following sets of rod readings were taken: Instrument set-up near A : BS on A = 1.719m, FS on B = 2.578m Instrument set-up near B : BS on A = 1.335m, FS on B = 2.176m Point A has a known elevation of 197.428m. Determine the elevation of point B.
The differential leveling runs from BM 10 to BM 11 at a distance of 7.5km. It was observed that the leveling rod was inclined 6º from the vertical every time the backsight is taken. The average BS reading is 3.15m and the average length per set-up is 300m. Determine the error every 300-m set-up and the correct elevation of BM 11 if the recorded elevation was 140.20m
From the following differential leveling notes, compute the difference in elevation between stations 5 and 6. a. 2.62 b. 1.61 c. 3.51 d. 1.87
In surveying of differential leveling runs from BM10 to BM11 at a distance of 7.5km. It was observed that the leveling rod was inclined 6º from the vertical every time the backsight is taken. The average BS reading is 3.15m and the average length per set-up is 300m. Determine the error every 300-m set-up and the correct elevation of BM11 if the recorded elevation was 140.20m
A line of levels is run from BM1 to BM2, which is 12 km long. Elevation of BM1 was found out to be 100 m, and that of BM2 is 125.382 m. Average backsight and foresight distance were 150 m and 100 m, respectively. If during the leveling process, the line of sight is inclined downward by 0.004 m in a distance of 10 m, what would be the corrected elevation of BM2?
A line of levels is run from BM1 to BM2, which is 12 km long. Elevation of BM1 was found out to be 100 m and that of BM2 is 125.382 m. Average backsight and foresight distance were 150 m and 100 m respectively. a) (Situation 1) If during the leveling process the line of sight is inclined downward by 0.004 m in a distance of 10 m, what would be the corrected elevation of BM2?
A line of levels is run from BM1 to BM2, which is 12 km long. Elevation of BM1 was found out to be 100 m and that of BM2 is 125.382 m. Average backsight and foresight distance were 150 m and 100 m respectively. if the average backsight reading is 3.4 m and every time it is taken, the rod is inclined to the side from vertical by 4°, what should be the corrected elevation of BM2?
For all the computed values with decimals, use four (4) digits after the decimal. Differential leveling runs from BM10 to BM11 at a distance of 7.5 km. It was observed that the leveling rod was inclined 6° from the vertical every time the backsight is taken. The average BS reading is 3.15m and the average length per set-up is 300m. Determine the error every 300m set-up and the correct elevation of BM11 if the recorded elevation was 173.20m.
Based on the level loop problem. What is the calculated elevation of BM_10 ?
Based on the level loop What is the calculated value of BM_13 before adjustment ?
Discuss the parts and functions of the Tilting Level, a leveling instrument. Include the references that will be used.