A distributed load that varies from 20 kN/m to 50 kN/m is applied as shown in the figure. Concentrated loads are also applied at point E and 10 kN force is applied to the cable attached to pulley D. Determine: a. The equivalent force-couple at point A, and b. Replace the force system by a single force and determine where the line of action of this force crosses the x and y axis. 0.15 m 0.15 m 7.5 kN 50 kN/m 45° 30 4.5 kN radius=0.05 m 10 kN Bi 20 kN/m 0.35 m 0.35 m to

A distributed load that varies from 20 kN/m to 50 kN/m is applied as shown in the figure. Concentrated loads are also applied at point E and 10 kN force is applied to the cable attached to pulley D. Determine: a. The equivalent force-couple at point A, and b. Replace the force system by a single force and determine where the line of action of this force crosses the x and y axis. 0.15 m 0.15 m 7.5 kN 50 kN/m 45° 30 4.5 kN radius=0.05 m 10 kN Bi 20 kN/m 0.35 m 0.35 m to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
A man exerted a force of 60 lbs at B as shown in the figure. Compute the angle theta in degrees. Compute the tension of the cable CAD in lbs.
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
Three cables are subjected to the horizontal force F at A as shown. The tension force TAB in cable AB is given 20 kN and joint A is in equilibrium.1) Draw the force diagram of the joint A; 2) Determine the unit vectors of TAB, TAC, and TAD; 3) Form three equilibrium equations in a scalar form for solving the magnitude of tension forces TAC, TAD, and horizontal force F; 4) Solve the magnitude of tension forces TAC, TAD, and horizontal force F. [Partial Ans: TAC = 50.7 (T) kN, F = 128 kN (right x direction)]
A cable ABCD is pulled at end E by a force P (Figure P6.12). The cable is supported at point D by a rigid member DF. Compute the force P that produces a sag of 2 m at points B and C. The horizontal reaction at support F is zero. Compute the vertical reaction at F.
A cable is attached to the 20 kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
A load W is to be lifted using the crane which is hinged at B as shown in the figure. The value of x1 is 10m, x2 is 8m and h is 18m. Neglecting the weight of the crane. Determine the following. 1. Force at cable AC. 2. Resultant reaction at B. 3. Largest load that can be lifted if the maximum force of cable AC is 50kN.
The tongs are used to grip the ends of the drillingpipe P. If a torque (moment) of MP = 800 lb ⋅ ft is neededat P to turn the pipe, determine the cable force F that mustbe applied to the tongs. Set θ = 30°.
The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 204 N and if a = 3m, determine the magnitude of force P(N). Round off only on the final answer expressed in 3 decimal places.
Consider the three-dimensional structure shown in the figure, fixed to the ground at point O, and restrained by cables AB and CD. The tension TT in the restraining cable CD is 2.8 kN. Calculate the magnitude of the vector moment (in kNm) produced by the force exerted by the cable CD on point C, about the point O (assume use of the right-hand rule). Take aa = 4.7 metres, and bb = 3.8 metres.
A man weighing [(70*B)+(8*E)] N stands at the middle rung of a steel ladder uniformly weighing [15+(4*A)] kN/m. Assuming that the floor and wall are perfectly smooth and that slipping is prevented by cable CD, determine the following: A. Tension in the cable B. Reaction at A and B the values are A=3 B=9 C=1 D=3 e=1