A drum with a 500-mm radius is attached to a disk with a radius of 250 mm. The disk and drum have a combined mass of 15 kg and a combined radius of gyration of 400 mm. A 12 kg block D is suspended by a wire that is warped around the drum. Another force P- 100 Nis applied to the wire that is warped around the disk. If the system is released from rest, neglecting the effect of axle friction determine: (a) the acceleration of the block. (b) the velocity of the block after 10 second. (c) the distance travelled by the block after 10 second. (d) the revolution by the drum just after 10 second. 500 mm 250 mm

A drum with a 500-mm radius is attached to a disk with a radius of 250 mm. The disk and drum have a combined mass of 15 kg and a combined radius of gyration of 400 mm. A 12 kg block D is suspended by a wire that is warped around the drum. Another force P- 100 Nis applied to the wire that is warped around the disk. If the system is released from rest, neglecting the effect of axle friction determine: (a) the acceleration of the block. (b) the velocity of the block after 10 second. (c) the distance travelled by the block after 10 second. (d) the revolution by the drum just after 10 second. 500 mm 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A spring of stiffness k = 500 N/m is mounted against the 10-kg block. If the block is subjected to the force of F = 500 N, determine its velocity at s = 0.5 m. When s = 0, the block is at rest and the spring is uncompressed. The contact surface is smooth. F= 500 N k - 500 N/m www Problem No. 8 The 2-Mg car is being towed by a winch. If the winch exerts a force of T = 100(s + 1) N on the cable, where s is the displacement of the car in meters, determine the speed of the car when s = 10 m, starting from rest. Neglect rolling resistance of the car.
The copper pipe (G - 45GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fxed at A and three torques are applied to it as shown. Solve the rotation of the free end with respect to the fixed end. A 200mm 250mm 3. 30 N-m 300mm 20 N m 80 N-m O 0.00125rad O 0.00112rad O 0.00104rad O 0.00237rad
Quizs- Replace the loading system by an equial ent resultant force and Couple moment acting at Point o. fi=l00 N Mc:75 Nm 0:3m 200 0-5 m 0.4m
P F 600 mm 2P 2P A E C 400 mm B D - The assembly consists of two 12.05 mm-diameter A992 steel rods AB and CD, a 20-mm- diameter 6061-T6 aluminum rod EF, and a rigid bar AEC. If P = 11.52 kN - determine the displacement of F. - Find the displacement of point F if the system is subjected to a change in temperature AT = 9.5 C. Only consider the change in temperature.
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
The outer and inner diameters of a 700mm long copper tube (E - 130GPA) are 100mm and 70mmm, respectively. If a torque of 10kNm was applied on the tube, solve the angle of twist. O 0.646 degrees O 0.722 degrees O 0.414 degrees O 0.517 degrees
Im 2m Im 2m A 14 kN A 8 kN-m B 8 kN-m V M Solve V and M diagram
Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt circle 320 mm in dia- meter and six 15-mm diameter bolts on a concentric bolt circle 240 mm in diameter. Determine the unit stress in each bolt due to a torque of 25 kN.m.
A solid circular drive shaft connects a motor to gears B and C. The drive shaft is steel (G= 66 GPa) with a diameter of d=35 mm. 600 N-m A 200 N-m (1) (2) 100 mm C. 300 mm
P8-1. Determine the friction force at the surface of contact. 500 N 3 W = 200 N plus 0.3 Mk = 0.2 100 N (a) (b) Prob. P8-1 W = 40 N μ = 0.9 Mk = 0.6 P P
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @5 Hz when constant 120 KW is applied. Use the following: G(alum)-28 GPa, a=1.80 m, b=0.80m & L-2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is_KN-m B E 1.18 0.48 2.64 3.82 5.03
A bracket connected to the flangé of a column through a group of rivets to transfer a load of 120 kN at an eccentricity of 150 mm as shown in the figure. The thickness of the bracket plate is 8 mm. Design the diameter of the rivets if the permissible stress in single shear is 100 MPa and in bearing 180 MPa. 120 kN 150- 4 p/n 30 60 60 60 G 60 30 90 +.