A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. - 20 cm - 15 em 500 turns 15 cm 15 cm Core depth 5 em

A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. - 20 cm - 15 em 500 turns 15 cm 15 cm Core depth 5 em

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic permeability is 200. its average length is 40 cm -The diameter of the cross-sectional area is 1 cm. Find the current that must pass through the winding to produce 0.5 mWb of flux in a 1mm air-gap magnetic circuit?
A ferromagnetic core with a relative permeability of 1500 is shown in the following figure. The depth of the core is 5 cm. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 300 turns in the coil wrapped around the center leg of the core, and if the current in the coil is 1.25 A, find the magnetic flux and the field density in all three legs of the core, as well as the magnetic flux and flux density in the two air gaps.
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a fluxdensity 3 T, the corresponding relative permeability of iron core is 1500. Determine thenumber of turns in the winding, given that the magnetic flux path has a mean length of 20cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2
An autotransformer is shown in Figure P14.68. Assume that all of the flux links all of the turns and that negligible mmf is needed to establish the flux. Determine the values of I1, I2, I3 and V2.
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a flux density 3 T, the corresponding relative permeability of iron core is 1500. Determine the number of turns in the winding, given that the magnetic flux path has a mean length of 20 cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2. * ROUNDING OFF is ALLOWED only in the final answers expressed up to FIVE (5) DECIMALPLACES.
For the electromagnet of Figure-a. Find the flux density in the core.b. Sketch the magnetic flux lines and indicate theirdirection.c. Indicate the north and south poles of the magnet.
1) A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm.a) Calculate the total reluctance, total, of the core
A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm. The Rtotal is found to be 226.192k At/Wb
Below you can find a ferromagnetic core and its magnetization curve. If i1=0.4 A and i2= 0.9A, find magnetic flux in the core and the relative permeability under these conditions.
A core with three legs is shown in the figure below. Its depth is 5 cm, and there are 400 turns on the centre leg. The remaining dimensions are shown in the figure. The core is composed of steel having the magnetization curve is also given below. Answer the following questions about this core: 1. What current is required to produce a flux density of 0.5 T in the central leg of the core? 2. What current is required to produce a flux density of 1.0 T in the central leg of the core? Is it twice the current in part (a)? 3. What are the reluctances of the central and right legs of the core under the conditions in part (a)? 4. What are the reluctances of the central and right legs of the core under the conditions in part (b)? 5. What conclusion can you make about reluctances in real magnetic cores?
For operation at 60 Hz and a given peak flux density, the core loss of a given core is 1W due to hysteresis and 0.5W due to eddy currents. Estimate the core loss for 400-Hz operation with the same peak flux density.