A fire has been happened near a wall in a building, suppose the heat transfer f(x, y) = y²-K(x² + equation in the wall will be according to the equation: 2x - xy) a- Compute the constant (K) if you know that the heat transfer equation satisfy the following differential equation a²fa²f + = 0 дх2 дуг b- Find the location of extreme heat value in the wall

A fire has been happened near a wall in a building, suppose the heat transfer f(x, y) = y²-K(x² + equation in the wall will be according to the equation: 2x - xy) a- Compute the constant (K) if you know that the heat transfer equation satisfy the following differential equation a²fa²f + = 0 дх2 дуг b- Find the location of extreme heat value in the wall

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.12P

See similar textbooks

Similar questions

The rate of heat flow per unit length q/L through a hollow cylinder of inside radius ri and outside radius ro is q/L=(AkT)/(rori) where A=2/(rori)/ln(ro/ri). Determine the percent error in the rate of heat flow if the arithmetic mean area (ro+ri) is used instead of the logarithmic mean area A for ratios of outside-to-inside diameters (Do/Dj) of 1.5, 2.0, and 3.0. Plot the results.
The same engineer decides to look into rates of cooling for liquids toexperiment with different cooling solutions for servers. She finds thatthe rate of cooling for one liquid can be modelled by the equation:y = 48 × 0.99t(0 ≤ t ≤ 80)where y is the temperature of the liquid in degrees Celsius and t is thetime in minutes.(i) State whether the type of reduction for this model is linear orexponential. Describe how reduction rate differs between linear andexponential functions. (ii) Calculate the temperature when t = 20. [3](iii) Write down the scale factor and use this to find the percentagedecrease in the temperature per minute. (iv) Use the method shown in Subsection 5.2 of Unit 13 to find the timeat which the temperature is 30◦(v) Determine the halving time of the temperature.
A cylindrical tank (1.20m in diameter) contains two liquids with the follow specific gravities:LIQUID 1: oil (s.g.oil = 0.80)LIQUID 2: water (s.g.water = 1.00)Each specified liquid has a thickness of 0.60m with the denser liquid at the bottom. If a circular office is placed at the bottom of the tank (100mm in diameter and with c = 0.65) to drain the fluids: Compute for the time required to remove the denser liquid from the tank. Hint/s: In evaluating the time to drain the more dense fluid, use the concept of equivalent pressure heads to evaluate hinitial and hfinal since there are multiple fluids in the container
Complete the following table for refrigerant-134a. Show your work and explain how you got your values. T (oF) P psia) h (Btu/Ibm) X Phase description 80 78 15 0.6 10 70 180 129.46 110 1.0
Find the rate of heat transfer if the cylinder in a stainless steel rod.k = 15 W/m·K (8.7 Btu/h·ft·F), L = 1 m (3.3 ft), Th = 200 C (392 F), Tc= 100 C(212 F), A = 5 cm2 (0.8 in2).
i post this question 4 times till now plzzz answer that question approve that the equations are equal by the integration
Liquid biofuel (density= 789 kg/m3) is being pumped from a storage tank through a pipe with 1-inch innerdiameter (ID). The fuel is being pumped at a rate of 3.00 gallons per minute. In this process, what is thekinetic energy transport rate (Ėk) in units of horsepower (hp) and ft•lbf/sec.
EXPERIMENT PROBLEM: A certain mechanical device with a mechanism similar to a piston contains a certain amount of gas. Upon compression from 55 L to 15 L, the gas released 350 J of heat. Experiment shows that the external pressure of the mechanical device is given by: Pext = AsinV + BcosV + CsinhV + DcoshV Where: A = 100 B = 80 C = 1x10⁻²⁵ D = 5x10⁻³⁰ sin = sine function cos = cosine function sinh = hyperbolic sine function cosh = hyperbolic cosine function V = in liters Pext = in atm Determine the change in internal energy of the system in kilojoules. TIP: usually, expressions involving trigonometric functions are in radians.
HEAT TRANSFER (a) Determine the thermal conductivity of an insulating material given the following data: steel pipe with 0.1025 m inner diameter and 0.1150 m outer diameter, insulation thickness 3 cm, heat flow per meter is 150 W/m, steel thermal conductivity 55 W/m-°C, and overall temperature difference of 72.2°C. If the temperature of the steam inside the pipe is 128°C, (b) find the outside temperature of the insulating material.
5.17 In the liquid heating tank shown in the figure below, density = 0.8g/cm^3, V=500cm^3, Cp=0.5cal/(g C), the total heat transfer area of the heating coil is 20cm^2, and the total heat transfer coefficient is 10cal/ (cm^2 hr C). Inside the coil, hot oil flows with a temperature of Tq. Find the temperature T(t) of the fluid when the temperature of the oil changes as shown in the figure at any moment, ignoring the temperature difference between the surface of the heating coil and the oil.
A parachutist has a terminal velocity of -176 feet per second. That is, no matter how long a person falls, his or her speed will not exceed 176 feet per second, but it will get arbitrarily close to that value. The velocity in feet per second, v(t), after t seconds satisfies the differential equation v′(t) = 32 - k *v(t). What is the value of k?
‏A simply supported beam is subjected to two forces P and Q. Value of force P is 20 N and value of force Q is 40 N.If value of support force Ra is 30 N , then value of support force Rb is calculated as : O a . 70 N O b.30N O C60N O d . SON