A footing (F1) has dimensions 1.2m x 1.2m x 0.3m. How many bags of cement shall be used for 10 pieces of F1? Use class “C” concrete and 40kg/bag of cement. ClassAAABCTABLE 1-2 CONCRETE PROPORTIONMixture1:11/2: 31: 2 : 41:21/251: 3 : 6Cement40 kg. /Bag 50 kg. / Bag9.57.06.05.012.09.07.56.0Sandcu.m..50.50.50.50Gravelcu.m.1.01.01.01.0

Reference : Concrete Technology, Number of cement bags. Given : Size of F1, Number of F1 and Class…

Answered: A footing (F1) has dimensions 1.2m x…

A footing (F1) has dimensions 1.2m x 1.2m x 0.3m. How many bags of cement shall be used for 10 pieces of F1? Use class “C” concrete and 40kg/bag of cement.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1 (AD) = St FIG. 7.13 TABLE 7.6 Segment AB BC 75 CD ED M₂M -dx EI B ABCD B 150 kN Į с (b) Real…

A: Calculate the vertical deflection at D using virtual work method

Q: A cantilever beam has the Cross-section of an isosceles triangle with a base and height equal to 1 m…

A: Given- Bending moment M=6 MN-m, Ymax=2d/3=2/3 m, I=1/18 m4,

Q: Part C-Analyzing another force-couple system on a bracket The same bracket and force-couple system…

A: Replace the force and couple system with an equivalent force by specifying the magnitude of the…

Q: Question 8 The difference in elvation is defined as: (Choose the best definition.) O the vertical…

A: Option (1) is the correct answer. The level surface is the surface parallel to the mean surface of…

Q: A singly reinforced rectangular concrete beam has a width of 150 mm and an effective depth of 330…

A: Given data: Beam width, b=150 mm. Effective depth, d=330 mm. The characteristics compressive…

Q: Determine the force in member BC of the loaded truss. The force is positive if in tension, negative…

Q: Problem 1. The following data relate to a closed traverse ABCD in which the bearings of the lines AB…

Q: A given cohesionless soil has emax = 0.85 and emin = 0.50. In the field, the soil is compacted to a…

Q: Comment on the significance of the estimated coefficients and interpret the meanings of the slope…

A: Asked about 1) significance of the estimated coefficients 2) interpret the meanings of the slope…

Q: What is the shear stress at the neutrsl axis in a beam of

Q: er. Linear error of closure is:

Q: What is 4,000,000 centesimal seconds in radian?

A: Option a

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

Q: In a table of leveling notes, the stations where the leveling instrument is set-up must be included…

Q: A car travelling at 40 mph on uphill grade of 5%. If the brakes are suddenly applied, it will travel…

A: uphill grade = 5% braking distance = 56m find out coefficient of friction ?

Q: Problem-5, For a reinforced concrete beam with M 20 concrete with Fe 415 steel, the working moment…

A: Given- M20 concrete, Fe415 steel, Balanced failure case, It is needed to find the value of A.

Q: (CILO5) The composite shape in Question 5 consists of a (1) square, (2) isosceles triangle. The…

A: For the given shape, the centroid and moment of inertia can be determine by dividing the shape into…

Q: Find the slope and deflection at B and E of the beam and loadings shown using area-moment method.…

Q: Draw shear and moment diagram

Q: Question 89 What is the shear stress at the neutrsl axis in a beam of isosceles triangular section…

A: Given- Base=40 mm, Height=20 mm, Shear force=3 kN,

Q: ,,Assuming the density of your concrete is 148 lbs/ft3, the box below would weigh approximately: 6"…

A: Objective: To determine the weight of the concrete box and choose the nearest option. Given:…

Q: Problem 5. If the center lines of the two parallel railway lines that are connected by a reverse…

Q: If the elevation of a previous point is 89.9 m and the rod reading taken on that point is 1.27 m,…

A: BS=backsight RL=elevation HI=height of instrument To find RL of line of sight at setup station

Q: A rigid pavement 160-mm thick and 8.10-m wide is to be provided with a center longitudinal joint…

A: We have calculate spacing of the longitudinal bar in mm. We have calculate that....

Q: What are the main types of engineered wood products?

A: One of the most popular natural building materials worldwide is wood. Several beneficial…

Q: Problem 2. The frame is loaded as shown in the figure. Assume the frame has hinge supports at A and…

A: Given data : determinate beam with internal hinge at D with pinned support at A and F Find : SFD ,…

Q: A survey of a closed traverse ABC shows the following latitudes and departures: Line AB latitude…

A: Given :- Closed Traverse ABC Latitude of line AB = 1997 m Latitude of line CA = - 1997 m To…

Q: Problem 1. The following data relate to a closed traverse ABCD in which the bearings of the lines AB…

Q: 2 kN/m 6 kN/m 6 kN/m 2.5 m 4m -6m- 6 m *Assume A and C to be pinned support, and B to be a flexible…

A: We have asked A And C is pinned support and B is flexible connection. Draw Bending moment Diagram…

Q: A 2650-N-m torque 7 is applied to the hollow shaft as shown. NOTE: This is a multi-part question.…

A: Using formula to find maximum shear stress

Q: What is Laminated Veneer Lumber? Explain Axis convention used for defining loading conditions for…

A: A multilayer mixture of wood veneers and adhesive is called laminated veneer lumber (LVL). It is a…

Q: Determine the deflection specified in each of the following beams. Use only one method to solve for…

A: Given data : Determinate beam with Pinned and roller support at A and C respectively Find : Mid span…

Q: Do not include the unit in writing the answer. Express all values up to 3 decimal places. You can…

A: To Complete the table and to answer the questions posed with respect to the Leveling calculations

Q: For a block with Young's Modulus of its material being 210 GPa and its Poisson's Ratio being 0.25,…

A: Given- Young modulus E=210 GPa, Poisson's ratio- μ=0.25, Stress- σx=60 N/mm2, It is needed to find…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: a. Determine the horizontal displacement at C. [Select] b. Calculate the slope at C. [Select]

Q: How did you get the f'c?

A: Given, Fy = 420 MPa (tension) Fy = 414 MPa (compression)

Q: wind speed at 10 ft above the ground is 20 mph. Plot the probable velocity profile to a height of…

Q: peated measurements on pean to ito

A: Precision is a term which indicates the degree of conformity of a. repeated measurements of the…

Q: Calculate the maximum allowable load in kN that a nominal 275mm x 275 mm sawn lumber column, 3.5m…

A: Given data: Size of the sawn lumber=275 mm×275 mm Length of the column, L= 3.5 m E= 9.78 GPa, Fc=…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: II. Classify each of the structures as statically determinate or indeterminate. If indeterminate,…

A: Given data in question Structures To find out Indeterminacy Note Ds= total static indeterminacy…

Q: The surveyor established the stadia interval factor of a theodolite by setting up the instrument 50…

Q: D 6 kN/m 4 m 3m *Assume A and C to be hinged supports, and B to be a pinned connection

A: Given: Required: Draw shear and moment diagram

Q: List the four classifications of steels. For each, briefly describe the properties and typical…

A: 4 classifications of steels. Based on material properties and design aspects.

Q: Determine the equations for shear and bending moment for the beam shown as a function of x. Take the…

A: To draw SFD and BMD

Q: NASEN 4 kN/m C B -6m 4.5 m sume A to be rocker, B to be fixed support, and C to be internal hinge.

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm.

A: Volume of 1=(40×17×38) - Volume of 2 =(40×17×38) - 12×10×10×17…

Q: The perception-reaction time for a vechile travelling at 80 km/h. Co-efficient of longitudenal…

Q: The completed flow net for the dam shown below includes a steel sheet-pile cutoff wall located at…

Question

A footing (F1) has dimensions 1.2m x 1.2m x 0.3m. How many bags of cement shall be used for 10 pieces of F1? Use class “C” concrete and 40kg/bag of cement.

Class
AA
ABC
TABLE 1-2 CONCRETE PROPORTION
Mixture
1:11/2: 3
1: 2 : 4
1:21/25
1: 3 : 6
Cement
40 kg. /Bag 50 kg. / Bag
9.5
7.0
6.0
5.0
12.0
9.0
7.5
6.0
Sand
cu.m.
.50
.50
.50
.50
Gravel
cu.m.
1.0
1.0
1.0
1.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Concrete Mix design

VIEW

Step 2 Find Volume of Single F1

VIEW

Step 3 Find Volume for 10 F1

VIEW

Step 4 Find total number of cement bags required

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

W (kN)=570 A (mm2)= 6500 Eal (GPa)=74 Est (GPa)= 205 ΔT (ºC)= 18
Abeam has a height of 710 mm and a width of 350 mm f'c = 28 MPa, fy = 420 MPa, and two layers of dia 12 mm(3 bars each) Stirrups Dia 10 mm Find MN?
ASAP PLS THANKS!
Listen What should you enter for the Total HAWB on the Consolidation Manifest? 2 34 14 20
14 - What is the meaning of Cant in Turkish? A) aliymanB) clearanceC) deverD) slopeE) ramp
Do fast i will give u thumsup sure
SHOW COMPLETE SOLUTION PLSVALUES:A= 5B= 5 C = 1
1. Concrete Hollow Block 200mm H x 400mm L x 150mm thk. per piece and Laying 8 layers x 4.5 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.80 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters A = 7.20m3 b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% N = 93 pcs c) How much mortar or grout is required in CHB laying? In cubic meters Answer: 0.5562 m3 d) How many bags of cement is needed if Class B Mixture is required? WF=3% Answer: 7 bags Answers are already given, solutions are needed.
Given: ▪ Proposed Eight-storey with roof deck commercial mix use building▪ 20 x 32 m with first floor being 3.5 meter in height and rest at 3.2 meter with 1.0-meter parapet ▪ 5 bays x 7 bays (5@ 4-meter x 8@ 4 meter typical) ▪ Assume a 10 kPa regular weight of the typical floor area except at roof deck being 8 kPa. Occupancy Category IIIEnclosedWind speed, V= 260kphExposure C Calculate the required wind pressure on the walls and parapet applying the code provision under Directional Procedure for Buildings of All Heights (NSCP section 207B) **ALL UNITS MUST BE IN KILOPASCAL (kpa)photos for reference
verifyy the Answer R_B=562lb and M_B =2324lb-in. (Show all the work within 20-30mins)
help me asap pls :((
Need asap pls. thanks