3 A footing (F1) has dimensions 1.3m x 1.3m x 0.3m. How many bags of cement shallbe used for 7 pieces of F1? Use class "B" concrete and 40kg/bag of cement. DONOT round off your final answer.ClassAAABCTABLE 1-2 CONCRETE PROPORTIONCementMixture 40 kg. /Bag 50 kg. / Bag9.57.06.05.01:11/2: 31: 21:21/2: 51: 3: 612.09.07.56.0Sandcu.m..5050.5050Gravelcu.m.1.01.01.01.0

Answered: Image /qna-images/answer/9f81a6b3-45ff-4257-88ee-2ad9d4c97473.jpg

Answered: A footing (F1) has dimensions 1.3m x…

A footing (F1) has dimensions 1.3m x 1.3m x 0.3m. How many bags of cement shall be used for 7 pieces of F1? Use class "B" concrete and 40kg/bag of cement. DO NOT round off your final answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. A new office park is considering to start an express bus service for workers. A survey of office…

A: Most studies aim to predict the share of trips made by each mode or the absolute number of trips…

Q: 7. Using the graph of sample height vs. log time, determine the coefficient of consolidation c, in…

Q: The mass center G of the 1535-kg rear-engine car is located as shown in the figure. Determine the…

A: Given: Load=1535kg Distance between front wheel and G=1309mm Distance between G and back wheel…

Q: 1. Five Bodies are available in a region where g = 9.785 m/s2 have the following data: A.Body A…

A: Given: Weight of body A=10 kN Mass of body B=10 slugs Weight of body C=1,000,000 grains Mass of body…

Q: A 3 - hinged parabolic arch of 16m span has its abutments A and B at a depth of 4m and 8m…

A: A three hinged parabolic arch is a statically determinate structure. The arch can be analyzed using…

Q: Q- What is end depth in free overall?

A: We have asked End depth in Free overall.

Q: Q1. If the absolute pressure in a tank is 140 kPa, determine the pressure head in mm of mercury. The…

A: Determine the pressure head in mm of mercury.

Q: Problem 5 -- Classify the soil to be used as a highway subgrade material using AASHTO classification…

A: Given: Liquid limit (LL) = 44% Plasticity index (PI) =24 % Percentage finer as per the table given.…

Q: Determine the vertical reaction at the roller support. 3 m 43.8 kN/m. -7.2 m- 29.2 kN/m 222.5 kN…

A: Determine all the reaction

Q: 2. Distribute the trip produced and attracted between 3 zones using the following tables of data…

Q: Question The state of 2D-stress at a point is given by the following matrix of stress: [100 30. 30…

A: Given- State of 2D-stress given- σx=100 MPa,σy=20 MPa,σxy=τxy=30 MPa, It is needed to find the…

Q: The rainfall on five successive days in a catchment were measured as 3, 8, 12, 6 and 2 cm. If the…

A: Given: Total runoff (R)=15 cm Rainfall for day 1=3 cm Rainfall for day 2=8 cm Rainfall for day 3=12…

Q: Problem 2. Determine the force in members CD, ED, and CF of the space truss and state if the members…

A: The given truss is shown below:

Q: coefficient of volume compressibility is

A: Given; Following data are given for the laboratory sample.σ'0=175 KPae0=1.1σ'0+∆σ'0=300…

Q: Find 5 internal forces of the truss members. Estimate the value and the location of 3 external axial…

A: Truss is given as shown in the figure above and it has been asked in the question to determine the 5…

Q: determinate, statically indeterminate, or unstable. If indeterminate, specify the degree of…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: For the cantilever steel beam [E = 300 GPa; 1= 129 x 106 mm4] shown in Figure, use the double-…

A: Given, E = 300 GPa I = 129 x 106 mm4 L = 2.5 m P = 50 kN/m wo = 90 kN/m

Q: Draw the shear and moment diagrams for the beam shown. After you have the diagrams, answer the…

A: Given : To Find :

Q: -lb force is applied to the wrench handle. The blade is bolted to a bracket attached to the motor…

A: Given:-force=25 lbTo find:-Nc

Q: Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106) mm4.…

Q: If G1-3% and G2=4%, the required vertical curve is a sag curve. O True False QUESTION 2 If G1=-4%…

A: Given:- A) The grades of the curve are:- G1 = 3% G2 = 4% To determine:- The required curve is a sag…

Q: a). Determine the forces of all the members of the truss shown by the METHOD of JOINTS. Tabulate…

A: a). Determine the forces of all the members of the truss shown by the METHOD of JOINTS. b).…

Q: Draw the V and M diagrams. Find Θa, θB and θC. show all steps

A: Using slope selection method

Q: 49. The following data are given for the laboratory sample. o = 175 kPa; e = 1.1;o+Ao = 300 kPa; e =…

Q: Design of reinforced concrete Why we Calculate Vu at a distance d from the support or at face…

A: Shear force: The force which is acting on the transverse direction of the flexural member (beam) is…

Q: The safe stress, for a hollow column carries an axial load of 2.1 × 103kN is 125MPa. If the external…

Q: There are OA has length I A Find B Chiven: L₁ = cm 42 = (0,85₁-357cm = 14 F₁ 143 F 13 A.B has leugh…

A: Given: F1→=135i+145j-75k kNF2→=60i-85j-75k kNF3→=-115i+65j-55k kNF4→=25i-25j-35k kNL1→=125i+0j+0k…

Q: Determine the reaction at the supports A, C, and E of the compound beam. 3 kN/m 12 kN

A: Given : Determine reaction at the support A, C and E ?

Q: Find the strain value Change in length=0.2 mm Initial length=100 mm

Q: 2-11. Classify each of the structures as statically determinate or indeterminate. If indeterminate,…

A: To Determine :- Classify each of the structures as statically determinate, statically indeterminate,…

Q: The transplantation of rice requires 10 days and total depth of water required during…

A: Given- Base period B=10 days, Total depth=48 cm, Effective rainfall=8 cm,

Q: QUESTION 12 1. A 40 cm well completely penetrates an unconfined aquifer of saturated depth 40 m.…

Q: The force of impact

A: Given data, Horizontal jet of water with its cross-sectional area. A= 0.0028 m2Velocity,V= 5…

Q: A recreational park is built near Buffalo Creek. An adjacent stream channel can carry a peak 5-year…

A: Given, peak flow =5 year flow of stream channel =200 m3/s

Q: A horizontal jet of water with its cross-sectional area of 0.0032 m² hits a fixed vertical plate…

Q: A new office park is considering to start an express bus service for workers. A survey of office…

Q: Q- What is end depth in free overall?

A: the solution of above problem is below:

Q: A simple horizontal curve has 35 degrees of curvature and subtends an angle of 110 degrees.

A: Given: Degree of curvature, D = 35 Degrees Angle subtended, Δ = 110 degrees Station PC = 3+65.00 ft…

Q: The parameter in Horton's infiltration equation [f(t) = f + (f-f)e-Kt] are given as, f = 7.62…

A: Calculate the cumulative infiltration at the end of 2 hours??

Q: For the construction of tunnels close to excavated types, it is common to find massive massifs, and…

A: Solution: Introduction: Tunnels are underground passages that are constructed through the mountains…

Q: Month June July July August September October November Dates 1-301 1-12 13-31 1-31 1-30 1-31 1-24…

Q: (D² - 4D + 4)y=

Q: A reinforced concrete beam has the following properties: Beam width = 320 mm Effective depth =…

Q: A 1.5 m 1.5 m 1 m + 0.75 m В с S

Q: etermine the deflection at point B of the beam show

A: Given:- EI=constant E=200GPa I=315 x 10 6mm4 Span=6.5m Load=67kN To find:- deflection at point B

Q: Earth-whose in situ weight is 112 lb/ef, whose loose weight is 95 lb/cf, and whose compacted weight…

A: The given data is as follows: In-situ weight of earth=112 lb/cfLoose weight of earth=95…

Q: Differentiate between 'low gravity' and 'high gravity' dams. Calculate the limiting height of low…

A: Differentiate between 'low gravity' and 'high gravity' dams. Calculate the limiting height of low…

Q: Q- What is end depth in free overall?

A: solution of above problem is below:

Q: After the population of C-City has evacuated due to regular occurrence of monsters, Saitama found…

A: Given Length of line AB=95m Bearing of line AB=S45'E Length of line AC=88m Length of line AD=43m…

Q: A horizontal jet of water with its cross-sectional area of 0.0032 m² hits a fixed vertical plate…

A: Given data, Cross section area of jet, a = 0.0032m² Velocity = v= 6m/s To find :- force of impact of…

Question

A footing (F1) has dimensions 1.3m x 1.3m x 0.3m. How many bags of cement shall
be used for 7 pieces of F1? Use class "B" concrete and 40kg/bag of cement. DO
NOT round off your final answer.
Class
AA
A
B
C
TABLE 1-2 CONCRETE PROPORTION
Cement
Mixture 40 kg. /Bag 50 kg. / Bag
9.5
7.0
6.0
5.0
1:11/2: 3
1: 2
1:21/2: 5
1: 3
: 6
12.0
9.0
7.5
6.0
Sand
cu.m.
.50
50
.50
50
Gravel
cu.m.
1.0
1.0
1.0
1.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

given data

VIEW

calculation of no. of 40 kg cement bags required

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Based on the figure below, solve for the following items: a. Total Volume of Concrete of Footing (considering the wastage) in cubic meters. b. No. of cement bags, the volume of sand (cubic meter), and gravel (cubic meter) for footing using Class B. c. Total Volume of Concrete of Column/Pier (considering the wastage) in cubic meters. d. No. of cement bags, the volume of sand (cubic meter) and gravel (cubic meter) for column/pier using Class A. Column - 0.40 x 0.40 meter Height of Column - 1.60 meters Footing - 2 x 2 meters Thickness of Footing - 0.40 meter Show your solutions.
Given the image, a.) determine the number of bags of cement required to construct the wall footing using class A. b.) A 7m will be constructed, determine the total bags of cement required if the wall is 4.2m high and the CHB used are 5". Use class C mixture.
Estimate the TOTAL quantity of cement, sand and gravel needed for 12 pieces of the typical concrete columns and footings. Use Class B concrete mix for columns and Class A concrete mix for footings. Details: Dimension of Footing: 0.85m x 0.85m Thickness of Footing: 0.35m Dimension of Column: 0.375m x 0.375m Total height of the structure including the footing: 4m How many 50 kgs/bag of cement are required for the construction of the footing?
a rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 385 kN LL = 292 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal punching shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.
Estimate the TOTAL quantity of cement, sand and gravel needed for 12 pieces of the typical concrete columns and footings. Use Class B concrete mix for columns and Class A concrete mix for footings. Details: Dimension of Footing: 0.85m x 0.85m Thickness of Footing: 0.35m Dimension of Column: 0.375m x 0.375m Total height of the structure including the footing: 4m How many 40 kgs/bags of cement are needed for the construction of the columns? How many cu.m. of sand is needed for the columns? Note: Assume that the minimum order is per 0.50 cu.m.
A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL= 306 kN LL = 241 kN Li Pc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA
A rectangular footing 2.3 m x 3.2 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the ultimate punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
A footing requires 8 bags of cement. If the water-cement ratio is 0.53, how many water (liters) shall be used in the mixture? Use 40kg/bag of cement.
A footing requires 4 bags of cement. if the water-cement ratio is 0.45, determine the amount of water(liters) that shall be used in the mixture. use 40kg/bag of cement.
30 A rectangular footing 2.3 m x 3.2 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
Show your solution and diagram. Design a square spread footing to support an edge column 460mm x 460mm in dimension. The allowable soil pressure is 478.5 KPa, unit weight of soil is 20.4 KN/m³, unit weight of concrete is 23.5 KN/m³, fć = 21 MPa, fy = 414 MPa, 75mm clear cover and 25mm diameter rebars both ways.
Estimate the TOTAL quantity of cement, sand and gravel needed for 12 pieces of the typical concrete columns and footings. Use Class B concrete mix for columns and Class A concrete mix for footings. Details: Dimension of Footing: 0.85m x 0.85m Thickness of Footing: 0.35m Dimension of Column: 0.375m x 0.375m Total height of the structure including the footing: 4m What is the total volume of the footing?