7. (a) For step-down chopper circuit, sourcevoltage Vs = 220 V, chopping periodT = 2000' us, on period = 600 µs, loadcircuit parameters-R=12, L = 5 mH and E =24 V(9 Find whether load current iscontinuous or not.(ü) Calculate the value of averageoutput current.füi) Computethemaximumandminimum values of steady stateoutput currents.

Answered: Image /qna-images/answer/b12a64b9-acac-48b8-9605-ba4286a1a28e.jpg

- (a) For step-down chopper circuit, source voltage V, = 220 V, chopping period T = 2000'us, on period = 600 µs, load circuit parameters- R =12, L = 5 mH and E =24 V () Find whether load current continuous or not. is (ü) Calculate the value of average output current. (üi) Compute the maximum and minimum values of steady state output currents.

- (a) For step-down chopper circuit, source voltage V, = 220 V, chopping period T = 2000'us, on period = 600 µs, load circuit parameters- R =12, L = 5 mH and E =24 V () Find whether load current continuous or not. is (ü) Calculate the value of average output current. (üi) Compute the maximum and minimum values of steady state output currents.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.53P

See similar textbooks

Similar questions

A 210 km long three-phase transmission line is operated on a 60 Hz network. Line Finally a 40 MVA power with 0.78 back power factor under 120 kV voltage is being shot. The conductor resistance value of the line is 0.10 Ω / km, the inductance value Since 1.30 mH / km and capacitance value is 0.001 µF / km, Medium Transmission Line establishing the equivalent circuit model; a) -Calculate the line current and voltage of the sending side. b) Calculate the power loss on the line. c) Calculate the% voltage regulation value of the line.
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:The per-phase constants of a 345-kV, three-phase, 150-km-long transmission line are resistance = 0.112/km, inductance-1.1 mH/km, and capacitance = 0.02 uF/km. The line supplies a 180-MW load at 0.9 power factor lagging. Using the nominal-m circuit, determine the sending-end voltage in kV. 351.2 349.3 348.7 350.8
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
If the values of real power and reactive power is specified for a bus, then it is called as PQ bus. Select one: True False
Investigate the challenges and solutions for integrating energy storage systems (ESS) with intermittent renewable energy sources in microgrids.
How do distributed energy resources (DERs) such as solar panels and wind turbines impact the operation and planning of power systems? Analyze their integration challenges.
A 500 kV, 60 Hz uncompensated three-phase transmission line is 500 km long. The line has three ACSR 1113-kcmil (Finch) conductors per phase with parameters Current carrying capability of single ACSR 1113-kcmil (Finch) conductor is 1,110 A. Calculate the theoretical maximum (steady state stability limit) real power that this line can deliver and compare with the thermal limit of the line. Assume VS = VR = 1.0 per unit and unity power factor at the receiving end.
Derive the full solution to the driven LRC circuit shown below using complex exponentials. Start withKirchhoff’s rule for the loop and assume a complex V (t) = V0eiωt (where by convention V0 is real) andassume that I(t) = I0eiωt where I0 is a general complex number (which can be written quite generallyas I0 = |I0|e−iδ), and where one gets physical answers at the end by taking the real part of thecomplex answers. Find an algebraic complex expression that expresses the sum of the voltages. Solve this expression directly using algebra, no pictures of “phasors” really required. Factor out the solution to obtain|I0|, δ, Z (the complex impedance), and the voltages across each element as a function of time.
How does power system planning and optimization incorporate demand-side management and energy storage technologies?
Consider a radial distribution system given in figure below supplied by a 100% reliable source and consisting of two feeders connected in series. Each feeder has Tf = 5000 h and Tr = 5 h. Calculate the Reliability Indices and total system availability (A). Mathematically prove that parallel interconnection is going to increase reliability for the above scenario.
Explain the concept of load flow analysis in power systems and its importance in ensuring system stability and efficiency.
Discuss the significance of FACTS (Flexible AC Transmission Systems) devices in enhancing power system stability.