A freeway section is estimated to carry an annual average daily traffic (AADT) of 40,000 vehicles per day. Directional factor (D) = 0.6. Use the If DDHV is 2,640 veh/h, what design hour is used for this freeway section? O a. 5th design hour O b. 10th design hour c. 30th design hour O d. 60th design hour

A freeway section is estimated to carry an annual average daily traffic (AADT) of 40,000 vehicles per day. Directional factor (D) = 0.6. Use the If DDHV is 2,640 veh/h, what design hour is used for this freeway section? O a. 5th design hour O b. 10th design hour c. 30th design hour O d. 60th design hour

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter9: Capacity And Level Of Service For Highway Segments

Section: Chapter Questions

Problem 8P

See similar textbooks

Similar questions

Determine the L.O.S of the road if PHF = 0.88, D= 60%, K=O.11, V=115 kph? For an Existing 4 lane freeway having the following features: • Lane and shoulder width = 12 ft, 6 ft, weekday commuter • Percent of trucks and buses = 8% and 4% respectively and Et =2.5, Eb =2.2• AADT = 35200 veh/day, Assume lane capacity * 2000 pc/hr
A 6-lane urban freeway is suggested to be designed with the following data: F.ADT = 45000 vpd, design hour factor= 0.12 and directional split = 65%. Rolling terrain, 10% trucks, 5% buses, 6% Rvs, PHF is 0.91 and all traffic are commuters. Then based on the HCM 2000 procedure, the equivalent passenger- car hourly flow rate is about
A six-lane freeway (three lanes in each direction) in a scenic area has a measured free-flow speed of 55 mi/h. The peak hour factor is 0.80, and there are 8% large trucks and buses and 6% recreational vehicles in the traffic stream. One upgrade is 5% and 0.5 mi long. An analyst has determined that the freeway is operating at capacity on this upgrade during the peak hour. If the peak-hour traffic volume is 3900 vehicles, b.) Determine vp
Find the upgrade and downgrade service flow rates and service volumes for an eight lane freeway with the following characteristics: (11 ft lanes, 2 ft right-side clearance, 4.2 ramps/mile, 3% trucks, good weather, regular drivers, PHF of 0.92) The segment in question is on a sustained grade of 3.5%, 1.5 miles in length.
(a) A six-lane freeway (three lanes in each direction) has regular weekday users and currently operates at maximum LOS C conditions. The lanes are 11 ft wide, the right-side shoulder is 4 ft wide, and there are two ramps within three miles upstream of the segment midpoint and one ramp within three miles downstream of the segment midpoint. The highway is on rollingterrain with 10% large trucks and buses (no recreational vehicles), and the peak-hour factor is 0.90. Determine the hourly volume for these conditions.
A four-lane rural freeway segment has a 510 m grade length of 2% upgrade followed by a 630 m grade length of 3%. The freeway has 3.4-m lane, 1.5m left-shoulder lateral clearances and interchanges spaced at every 25 km. During the peak hour, there are 6% trucks, 2% buses, 2% recreational vehicles and the rest are passenger cars. Driver population adjustment is determined to be 0.90, peak hour factor is 0.90 and the BFFS is 110 km/h. At present, the freeway operates at capacity during the peak hour in the direction in question. If an additional 3.4 m lane is introduced, and all other factors stay the same, what will be the new level of service?
A six-lane freeway (three lanes in each direction) has regular weekday users and currently operates at maximum LOS C conditions. The lanes are 3.5m wide, the right-side shoulder is 1.2 m wide, and there are two ramps within three miles upstream of the segment midpoint and one ramp within three miles downstream of the segment midpoint. The highway is on rolling terrain with 10% large trucks and buses (no recreational vehicles), and the peak-hour factor is 0.90. a) Determine the hourly volume for these conditions. b) At one point along this freeway, there is a 4% upgrade with a directional hourly traffic volume of 5000 vehicles. How long can this grade be without the freeway LOS dropping to F?
A new section of a freeway is to be designed with a free-flow-speed of 65 mph along of 0.75 mile on 5% upgrade. The expected traffic volume is 4200 v/hr. The traffic composition is 15% trucks, 5% recreational vehicles, and 10% buses. The peak hourly factor is 0.9, the unfamiliar driver factor is 0.95. If the design requirement is to target a level of service (B), how many lanes must be provided to satisfy the design requirement?
A new section of Richmond Highway is being designed as a six-lane facility (three in each direction) with a two-way left-turn lane. Determine the peak-hour LOS. (Assume commuter traffic, 5% trucks, and no RVs.) Traffic data: demand volume = 3,120 veh/h PHF = 0.95 assumed base free-flow speed = 55 mi/h Geometric data: urban setting rolling terrain lane width = 11 ft shoulder widths = 4 ft (right side) and 1 ft (left side) average access point spacing = 12 points per mile on each side LOS A LOS B LOS C LOS D LOS E LOS F
Given four lane urban freeway, directional peak flow 1950 veh/hr. 5% truck PHF-0.9 rolling terrain with ideal condition for the road. Determine:1- Level of service of the operation. 2- How much additional traffic before reaching capacity
An existing four-lane freeway in rural area is with the following :information Lane width 3.5m, 0.9m lateral clearance, 1800 veh/hr peak hour volume, PHF=0.9, interchange density =0.90, 5% trucks, 5% buses and the road is within a mountainous terrain. Then based on the HCM procedure, the service flow rate (pc/h/In) is
A six-lane freeway (three lanes in each direction) has regular weekday users and currently operates at maximum LOS C conditions. The lanes are 11 ft wide, the right-side shoulder is 4 ft wide, and there are two ramps within three miles upstream of the segment midpoint and one ramp within three miles downstream of the segment midpoint. The highway is on rolling terrain with 10% large trucks and buses (no recreational vehicles), and the peak-hour factor is 0.90. b.) Determine the adjustment factor (f). (Express in three decimals)