A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. P f N/mm2 D Cross section

A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. P f N/mm2 D Cross section

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.10P

See similar textbooks

Related questions

Q: 3.8 The soil profi le at a site for an offshore structure is shown in Figure P13.8. The height of…

A: Given:- The height of the pile above the sand surface = 15 m The diameter of the pile = 1.25 m The…

Q: Following is the variation of N60 with depth in a granular soil deposit. A concrete pile 9 m long…

A: Calculate the range of values of the standard penetration number, the influence length of the pile…

Q: Problem 1 A 30 m long concrete pile is 305 mm x 350 mm in cross section and is fully embedded in a…

Q: A rectangular pile (0.67 x 0.5 m.) is driven in a clayey soil arrangement composed of two different…

Q: 2. Consider a group of 450 mm x 450 mm reinforced concrete piles were driven into thick loose sand…

A: Given data, size of pile=450 mmx 450mm unit weight of loose sand soil,γ=16 kN/m3 Internel friction…

Q: The section of a sheet pile is shown in the figure. The coefficient of permeability of the soil is…

Q: A 16 in diameter, 55 ft long drilled displacement pile is to be constructed in the following soil…

A: Calculate the Toe Bearing capacity: The construction method for DD piles does not provide any…

Q: Asteel pipe pile having a diameter of 0.35 m is driven 15 m into a loose sand with a unit weight of…

A: Given data: Diameter of the pipe = 0.35 m Depth of driven = 15 m Angle of internal friction = 33o…

Q: 2. Consider a pipe pile having an outside diameter of 500mm. The embedded length of the pile in…

A: Given, Pile diameter (D) = 500 mm or 0.5 m Embedded length (L) = 22 m

Q: Explain in your words the following : Pile Cap and Settlement of pile group in clay

A: Solution: In this, the settlement value is calculated by using the results that are obtained during…

Q: A frictional pile with a circular cross-section (diameter = D) is pushed into the soil to a distance…

A: The unit skin friction is taken equal to the shear strength multiplied by the reduction factor. Let…

Q: Refer to Figure 9.42b. Let L = 18 m, γfill = 17 kN/m3, γsat(clay) = 19.8 kN/m3, Φ'clay = 20°, Hf =…

A: The downward drag force will be: Qn=pK'yf Hf tanδ'L1+L12pK'y'tanδ'2 ...(1)The neutral…

Q: 1 A steel pile (H-section; HP 360 x 152; see Table 11.1) is driven into a layer of sandstone. The…

A: qud=qulab5qud=78.7MN·m-25=15.74MN·m-2Nϕ=tan245+ϕ2=tan245+362=3.852

Q: Refer to the pile shown in Figure P 9.1. Estimate the side resistance Qs bya. Using Eqs. (9.40)…

A: Coyle and Castello analyzed 24 large–scale field load tests of driven piles in sand. from the basis…

Q: A circular pile having a diameter of 0.44 m is 16.41 m long which is embedded in a layer of dense…

Q: A 3 x 3 pile group with pile spacing of 1 m and pile diameter of 0.40 m supports a load of 3 MN.…

A: The load on the pile is P=3 MN. The void ratio is e=0.65. The coefficient of consolidation is…

Q: A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a…

Q: A rectangular pile (0.52 x 0.82 m) is driven in a clayey soil arrangement composed of two different…

Q: A pile of 50 cm diameter is constructed in a dense sand of unit weight 19 kN/m³ upto a depth of 12…

Q: A section of a 3 x 4 group pile in a layered soil is shown below in Fig. 2. The piles are square in…

Q: A circular pile having a diameter of 0.33 m is 14.21 m long which is embedded in a layer of dense…

Q: Given: Anchored sheet pile shown in figure. Required: For a factor of safety of (2) with respect to…

A: Given: The factor of safety with respect to passive resistance = 2 Load acting, P = 40 kPa γ=16…

Q: A 16 in diameter, 45 ft long drilled displacement pile is to be constructed in a silty sand with 30…

A: Given- d=16 inl=45ftd=20ftFOS=2.8

Q: Given: Anchored sheet pile shown in figure. Required: For a factor of safety of (2) with respect to…

A: Given Factor of safety, FOS=2 Consider the free body diagram ;

Q: A 300 mm diameter steel pipe pile with 10 mm wall thickness is to be driven to a depth of 15 m in a…

A: The workload of the building creates a vertical displacement of the soil surface, which is known as…

Q: (b) A single test pile, 300 mm diameter, is driven through a depth of 8 m of clay which has an…

Q: An anchored sheet pile is to support a mass of cohesionless soil up to a height of 6 m above ground…

A: Given Unit weight of soil=21 KN/m3 Angle of internal friction= 30°

Q: A- The load (Q=900 ton) locate at x, determine the max. & min. pile reaction for the given condition…

A: The pile is the supporting or substructure for the bridge or building when loading is acting due to…

Q: Determine the allowable load for a steel closed-ended pipe pile, 0.4 m in diameter, driven 20 m…

A: Calculating the stress value at different location: σ1'=18×5-9.815=40.95…

Q: In Hiley’s formula for driven piles i.e. R=E/(s+0.5c), why is a coefficient of 0.5 applied for the…

A: Answer Hilley's Formula is based on the principle of energy of conservation.

Q: 20 m long bored concrete pile having a diameter of 350 mm is load tested, and the data are given…

A: Given:- L= 20 m d = 350 mm Econcrete = 25*1000 MN/m2 FS = 2.5 Max load = 1250 kN To find:- a)…

Q: d. Starting out from the condition where the water table is above the excavation line on both sides…

A: Brief concept introduction- Sheet Pile- Sheet piles are used to support earth retention and…

Q: A concrete pile 50 ft long having a cross section of 15 in. x 15 in. is fully embedded in a…

A: Precast concrete piles are used to build foundations for various structures in civil engineering and…

Q: PROBLEM 2: A circular pile 0.45m in diameter and 15m long is embedded in a layer of dense sand. The…

Q: Check the pile load of the Railroad Bridge of (hilla) for 4000 KN with pile diameter (1 m). The…

Q: Determine the diameter of 70 ft long pile driven in the medium dense sand (Shown in Figure). Design…

Q: Determine the ultimate load capacity of a circular pile with diameter D = 20 cm installed in a…

Q: A frictional pile with a circular cross-section (diameter = D) is pushed into the soil to a distance…

A: We know here to Derive a formula to calculate the normal stress in any section x.

Q: A 0.45 m square prestressed concrete pile is to be driven at a site of 15 m long where soil…

A: Given, B = 0.45 m L = 15 m

Q: A frictional pile with a circular cross-section (diameter = D) is pushed into the soil %3! to a…

Q: A 20-m-long concrete pile is shown in Figure P9.1. Estimate the ultimate point load Q, by a.…

Q: 1322.744

Q: Q1/ For the footing shown in Figure (1). estimate the pile group capacity. 0.6m dia bored pile Clay…

A: Ultimate load carrying capacity of pile: It is the maximum load which can be applied on pile without…

Q: Figure below shows a group pile in clay. Determine the consolidation settlement of the group. Use…

A: The given diagram is Shown below,

Q: n to the soil as shown below. Calcu

Q: Consider a 15 m long concrete pile with a cross section of 0.45 m x 0.45 m fully embedded in sand.…

A: Meyerhof (1963) proposed a recipe for computation of bearing limit like the one proposed by Terzaghi…

Q: A square concrete pile of 10 m length is driven into a deep layer of uniform homogeneous clay. The…

A: given- Length of pile=10 mUCS=100 kPaultimate load P=632 kN

Q: Determine the amount of axial shortening that the friction pile undergoes in service. Assume that…

A: Draw the figure. We know that, the deflection of the member due to its self weight acting downward…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

100%

A frictional pile with a circular cross-
section (diameter = D) is pushed into
the soil to a distance (L) and then it is
%3D
subjected to an axial force (P) on its top
end. Derive a formula to calculate the
normal stress in any section x.
f N/mm2
D
Cross section
Maximum size for new files: 128MB
Files

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular pile having a diameter of 0.33 m is 14.21 m long which is embedded in a layer of dense compacted sand having the given properties. Soil properties: Lateral pressure factor, K = 3.53 Nq = 99 Specific gravity, Gs= 2.61 Void ratio, e =1.21 Saturation above the GWT = 0.41 Ground water table (GWT) is located 3.58 m below the ground. Use unit weight of water = 9.81 kN/m3 Coefficient of friction = 0.41 Factor of safety = 3.98 Calculate the allowable capacity of the pile in kN.
What is 'negative skin friction' on pile and why does it causeconcern? How do you estimate its value in clay and sandy soil? Suggestmeans of controlling it.
An 18 in diameter, 75 ft long ACIP pile is to be constructed in the following soil profile: Depth(ft) SoilDescription Unit Weight(lb/ft3) Undrained ShearStrength(lb/ft2) EffectiveFrictionAngle(deg) SPTN60 0–15 Silty sand 120 28 15–40 Clayey silt 115 1500 40–60 Sandy silt(nonplastic) 119 25 60–70 Well-gradedsand 124 32 70–90 Well-gradedsand 127 35 40 The groundwater table is at a depth of 25 ft. Using a factor of safety of 3.0, determine the ASD allowable downward load capacity.
Explanation of nouns: 1. Static pressure pile 2. Soil penetration 3. Mechanical connection of steel bar
The circular concrete pile (γc=23kN/m3) of Figure Q2 has dimensions which depend on the ultimate (j) and the penultimate (i) digit of your ID number as described by the formulae in Table Q2. It is constructed inside a sand with shear strength characteristics as given inTable Q2 as well. Calculate the safety factor for a working load equal to Q=300kN. Note : My ID Number is 9477287
Redo Problem 9.23 assuming that the water table coincides with the top of the fill and that γsat(fill) = 19.8 kN/m3. If the other quantities remain the same, what would be the downward drag force on the pile? Assume ẟ' = 0.5 Φ'fill.
20 A rectangular pile (0.75 x 0.93 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 5 m., cohesion of 53 kPa, friction factor of 0.88. Second layer has a height of 8 m., cohesion of 78 kPa, and friction factor of 0.84. Compute the allowable load that the pile can carry if the factor of safety is 2.17. Round off to two decimal places.
Calculate the steel of spiral stirrups for a circular pile of X meter height where X is 133 and diameter of 1.25 meter, take overlap as 40D for every 25 meter length of spiral, pitch as 12 cm, diameter of spiral bar as 12 mm and concrete cover as 8 cm.
Please help me solve The soil profile and soil properties at a site are shown in the table below. A group of 12 concrete piles in a 3 x 4 matrix and of length 12 m is used to support a load. The pile diameter is 0.45 m and pile spacing is 1.5 m. Determine the allowable load capacity for a factor of safety of 2. Calculate the total settlement (elastic and consolidation) under the allowable load. Assume Ep 520 x 106 kPa.
Question 12 A rectangular pile (0.65 x 0.53 m.) is driven in a clayey soil arrangement composed of two different layers. First layer has a height of 7 m., cohesion of 50 kPa, friction factor of 0.83. Second layer has a height of 9 m., cohesion of 79 kPa, and friction factor of 0.88. Compute the allowable load that the pile can carry if the factor of safety is 2.55. Round off to two decimal places.
Help me solve please A pile with a square cross-section, B × B = 0.5 m × 0.5 m, is driven in a clay soil which has anundrained strength of 40 kPa at the ground surface, increasing thereafter by 3 kPa per meterdepth. a) Determine the required length of an individual pile which is supposed to take a load of500 kN on its top. Assume the factor of safety of 1.5 for both side shear and base resistance.The side shear on the pile may be taken as 55% of the soil’s undrained strength (show all steps)
A concrete pile 20 m long with a cross section of 400 mm x 400 mm is fully embedded in a saturated clay layer. The clay has the following properties: γsat = 18.5 kN/m3, ϕ= 0 and cu = 70 kPa. Assume that the water table rises to the tip of the pile. Determine the allowable load that the pile can carry (FS=3). Use the α and λ method to estimate the skin resistance.