A girder ABCDE bears on a wall for a length BC and is prevented from overturning by a holding-down bolt at A. The packing under BC is so arranged that the pressure over the bearing is uniformly distributed and the 30 kN load may also be taken as a uniformly distributed load. Neglecting the mass of the beam, draw its bending moment and shearing force diagrams. (Cambridge) 7.11

A girder ABCDE bears on a wall for a length BC and is prevented from overturning by a holding-down bolt at A. The packing under BC is so arranged that the pressure over the bearing is uniformly distributed and the 30 kN load may also be taken as a uniformly distributed load. Neglecting the mass of the beam, draw its bending moment and shearing force diagrams. (Cambridge) 7.11

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that it approximately loads the cable by a uniform q(x) = qo. If [= 10 m, ha = 5 m, and he = 4 m, compute the maximum force in the cable for its minimum distance to the ground by 3 m. B y hA hB a (deg) = 16.446 q0 (Kn/m) = 37.632
Determine the moments at all supports. Answer key: MBA = 2 kN-m; MBC = -2 kN-m; MCB = 4.46 kN-m; MCD = -4.46 kN-m; MDC = 0.66 kN-m; MDE = -0.66 kN-m; MED = 3.27 kN-m
Replace the loading system acting on the post by an equivalent resultant force and couple moment at point B.
The steel framework is used to support the 100-mm reinforced stone concrete slab that carries a uniform live loading of 5 kN/m2. Sketch the loading that acts along members BE and FED. Set a = 3m, b = 5m. Hint: See Table 1.2
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
What is the VERTICAL and HORIZONTAL reaction of the support at B?use :x = 137y = 37a = 6b = 8c = 1
1. The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom Neglect the weight of the boom. Draw the FBD
Determine the magnitude of the moment of the forceF = {50i - 20j - 80k} N about the base line BC of the tripod.
Replace the force system acting on the post by a resultant force and couple moment at point O.
A horizontal beam AB is freely supported at A and B, 8metres apart and carries uniformly distributed load of 15KN/m run (including its own weight). A clockwise moment of 160KN-M is applied at a point C, 3metres from left hand support A.using Macaulay method, calcite the beam at C if El=40×10^3KN-m^3
Determine the magnitude of the moment of the forceF = {50i - 20j - 80k} N about the base line AB of the tripod.
For the given loads w = 36 KN/m and M=90 KN.m is supported as shown by a roller at D and a hinge at D 1- Magnitude of reaction at D is (KN) : (a. 72 - b. 180 - c. 144 - d. 216 - e. 252 ) 2- Magnitude of reaction at A is (KN): (a. 72 - b. 108 - c. 252 - d. 36 - e. 180 ) 3- Bending moment just to the right of B (KN.m) : (a. -36 - b. -54 - c. -72 - d. -90 - e. -108) 4-Find Shear force just to the right of D 5- Find Shear force just to the left of D 6- Find Maximum absolute value of bending moment (KN.m) is