A hand-carved sample of clay having a mass of 2.62 kN is removed from a 0.5 meter- diameter hole. The hole can be filled with 1.33 kN of water. A sample of clay having a mass of 112.4 grams is oven-dried and has a dry mass of 103.6 grams. Assuming the maximum and minimum attainable unit weight of 18.47 kN/m3 and 16.33 kN/m3 and specific gravity of 2.67, what is the relative density of the soil in percent? Relative Density= %

A hand-carved sample of clay having a mass of 2.62 kN is removed from a 0.5 meter- diameter hole. The hole can be filled with 1.33 kN of water. A sample of clay having a mass of 112.4 grams is oven-dried and has a dry mass of 103.6 grams. Assuming the maximum and minimum attainable unit weight of 18.47 kN/m3 and 16.33 kN/m3 and specific gravity of 2.67, what is the relative density of the soil in percent? Relative Density= %

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Weight-volume Relationships And Plasticity

Section: Chapter Questions

Problem 3.20CTP

See similar textbooks

Similar questions

If a representative clay specimen 20 mm thick, under double drainage, took 121 minutes for 90% primary compression, estimate the time in days required for 50% primary compression of a field layer 2 m thick, bounded by impervious boundary at the bottom and sand at the top.
An undisturbed sample of clay has a wet mass of 30 kg, a dry mas of 25kg, and a total volume of 0.014 m3, and a specific gravity of 2.65. What is the porosity and void ratio?
Saturated silty clay encountered in a deep excavation is found to have a water content of 15%. Determine the unit weight of clay. G=2.7
8. An exploratory drill hole was made in a saturated stiff clay having a water content of 32%. It was observed that the sand layer underlying the clay was under artesian pressure water in the drill hole rose to a height of 4 m. above the top of the sand layer. If an open excavation is to be made in the clay. (See picture below) Determine the void ratio of clay. (Answer: 0.864) Determine the saturated unit weight of clay. (Answer: 18.76 kN/m3) How deep can the excavation proceed before the bottom of the saturated clay heaves or when its effective stress is zero. (Answer: 5.91 m)
A layer of sand 6 m thick lies beneath a clay stratum 5 m thick and above abed thick shale. In order to determine the permeability of sand, a well was driven to the top of the shale and water pumped out at a rate of 0.01m3/sec. Two observation wells driven through the clay at 15m and 30 m from the pumping well and water was found to rise to levels of 3m and 2.4 m below the ground water surface. Calculate the permeability of soil.
The compression diagram of a pre-compressed clay indicates that it had compressed under a pressure of 240 kN / m2. The compression ratio is 0.9; Your space vacuum under a pressure of 180 kN / m2 is 1.5. Estimate the void ratio if the effort s increases to 360 kN / m2.
The compression diagram for a precompressed clay indicates that it had been compressed under a pressure of 240 kN/m2. The compression index is 0.9; its void ratio under a pressure of 180 kN/m2 is 1.5. Estimate the void ratio if the pressure is increased to 360 kN/m2. a. 0.70 b. 1.246 c. 1.46 d. 1.34
a soil sample taken from subsurface exploration activity has the following properties: Gs= 2.67, e = 0.45, and S= 40%. a. Evaluate the unit weight of the soil in kN/m³. b. Evaluate the unit weight of the soil when dry in kN/m³. c. Evaluate the unit weight of the soil when fully saturated in kN/m³.
Boreholes reveal that a thin layer of alluvial silt exists at a depth of 50 ft below the surface of the ground. The soil above this level has an average dry unit weight of 96 lb/ft3 and an average water content of 30%. The water table is approximately at the surface. Tests on undisturbed samples give the following data: cu = 1008 lb/ft2, undrained friction angle = 13°, cd = 861 lb/ft2, drained friction angle = 23°. Estimate the shearing resistance in psf of the silt on a horizontal plane when the shear stress builds up rapidly. with fbd a.2185 b.2449 c.861 d.3120
Boreholes reveal that a thin layer of alluvial silt exists at a depth of 50 ft below the surface of the ground. The soil above this level has an average dry unit weight of 96 lb/ft3 and an average water content of 30%. The water table is approximately at the surface. Tests on undisturbed samples give the following data: cu = 1008 lb/ft2, undrained friction angle = 13°, cd = 861 lb/ft2, drained friction angle = 23°. Estimate the shearing resistance in psf of the silt on a horizontal plane when the shear stress builds up SLOWLY a. 2185 b. 3120 c. 861 d. 2449
An exploratory drill hole was made in a stiff saturated clay, as shown in Figure 1, having a moisture content of 25% and Gs = 2.56. The sand layer underlying the clay was observed to be under artesian pressure. Water in the drill hole rose to a height of 3 m above the top of sand layer. If an open excavation is to be made in the clay. a.What is the maximum depth of excavation before the bottom heaves? b.What would be the required height of water inside the cut in order to ensure a factor of safety of 1.5?
1) A dry rock weighs 240 grams and has a bulk density of 2.5 grams per cubic centimeter. Whensaturated with pure water at room temperature (T = 25 °C), it weighs 255 grams. At room temperature,specific volume of water is 1.00295E-03 m3/kg. Calculate the porosity of the sample. 2) A cylindrical core sample of 1.5 cm length and 1.2 cm2cross-section has upstream and downstreampressures of 2 atm and 1.25 atm, respectively, during steady state flow of water at 1.00 g/s at roomtemperature. Calculate the permeability of the core. (Water @ 25 °C, viscosity = 1 cp, density of water = 0.997 g/cm3).